Abstract:To achieve high-quality friction stir welding (FSW) of the rocket fuel tank, experiments of FSW 18 mm thick 2219 aluminum alloy are carried out, the microstructure and mechanical properties of the joints are studied, and the influence law of the tool rotation speed on microstructure, microhardness and tensile strength of the welded joints are explored. The welding speed used in the experiment is 100 mm/min, and the tool rotation speed is 350 r/min, 400 r/min and 450 r/min, respectively. The microstructure of the weldments is analyzed by optical microscopy and scanning electron microscopy. The mechanical properties are measured by tensile tests and Brinell hardness, and it is found that the mechanical properties of the joint first increased and then decreased with the increase of the tool rotation speed. Due to the uneven temperature distribution along the thickness direction of the weldment, the crystal grains in the nugget zone (NZ) are small equiaxed crystals as a whole, with different local sizes and shapes. The size of the crystal grains seems relatively large in the upper layer and relatively small in the bottom layer. As the tool rotation speed increases, so does the heat generation, and thus, the size and degree of the deformation of the crystal grains increase. The defect appears when the tool rotation speed is 450r/min. As the tool rotation speed increases, the tensile strength and microhardness of the joints increase first and then decrease. The maximum tensile strength of the overall weld is 270 MPa. The microhardness shows a trend of ‘‘U’’ distribution, and the hardness in the NZ is slightly higher than that of thermos-mechanically affected zone (TMAZ) and heat-affected zone (HAZ). The fracture location of the joints is the NZ. The fracture mode is ductile fracture. There exist a large number of second phase particles Al 2 Cu in the dimples.

Microstructure and Mechanical Properties of Ultrahigh‐Speed Friction‐Stir‐Welded Joints of In Situ Al 3 Zr Particle‐Reinforced Aluminum Matrix Composite Sheets

Microstructure and Mechanical Properties of Ultrahigh‐Speed Friction‐Stir‐Welded Joints of in Situ Al3Zr Particle‐Reinforced Aluminum Matrix Composite Sheets

Microstructure and mechanical properties of friction stir welding joint of in-situ ZrB2/AA7085 composites

Effect of rotational speed on friction stir welding microstructure and properties of cast and rolled (ZrB2 + Al3Zr) particle-reinforced aluminum matrix composites

Microstructural Characterization and Mechanical Properties of 120-mm Ultra-thick SiCp/Al Composite Plates Joined by Double-Sided Friction Stir Welding

Mechanical Properties and Their Relations to Microstructural Characteristics of High-Speed Friction Stir-Welded AA6005A-T6 Aluminum Hollow Extrusions

Correlation Between Microstructures and Mechanical Properties of High-Speed Friction Stir Welded Aluminum Hollow Extrusions Subjected to Axial Forces

Microstructures and Mechanical Properties of Micro Friction Stir Welding (μfsw) of 6061-T4 Aluminum Alloy

Microstructure, mechanical and fracture properties of friction stir welded 2195 Al-Li alloy joints

Study on Microstructure Evolution and Strengthening and Toughening of Friction Stir Processed AA6082-4%Al3Zr In-Situ Composites

Relationship Between Microstructures and Microhardness in High-Speed Friction Stir Welding of AA6005A-T6 Aluminum Hollow Extrusions

Effect of welding speed on microstructure and mechanical properties of Al−Mg−Mn−Zr−Tialloy sheet during friction stir welding

Microstructure and Mechanical Properties of Static Shoulder Friction Stir Welding AA3003-H14

Microstructure and mechanical properties of underwater friction stir welding of CNT/Al-Cu-Mg composites

Microstructure and mechanical properties of FSW medium thickness 2219 aluminum alloy

Improving microstructural and mechanical properties of dissimilar friction stir welded AZ61/AZ40 joint

Microstructure and properties of friction stir welding 6061 aluminum alloy joint

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Microstructure, mechanical properties and corrosion of friction stir welded 6061 Aluminum Alloy

Microstructures and Mechanical Properties of Al-Li Alloy Friction Stir Weld

Inhomogeneity of Microstructure Evolution in Stir Zone of 2195al Thick-Plate FSW Joints