Abstract:The development of friction stir welding (FSW) created the basic foundation for friction stir processing (FSP). This process entails refining the local microstructure and achieving the localised plastic deformation due to the stirring effect of the tool, which may involve adding additional filler material as required. The rotating tool involved in the process has a shoulder and pin responsible for heat generation for plastic deformation and localised mixing. The rotating tool is inserted and traversed on the desired surface, tailoring the material properties. The tool's exposure to the surface causes localised plastic deformation and thermal gradient, and microstructural changes occur locally. The present investigation uses Friction Stir Processing (FSP) to fabricate an aluminium metal matrix composite. Recently, the use of aluminium alloy has been replaced by composites because of their increased mechanical and physical properties (specific properties). The experiment leads to manufacturing an aluminium metal matrix composite using aluminium oxide, boron carbide and commercially pure copper dust. Later, the effect of heat treatment on the respective metal matrix composite is studied. A comparative study among three different types of FSP techniques viz. FSP, Reinforced FSP, and Heat-treated Reinforced FSP have been performed. The tool revolution speed (RPM) and tool traverse speed of 400 RPM and 10 mm/min had been implemented, respectively. The T4 Heat-Treatment cycle was used during the current investigation. This investigative study was performed to analyse the changes in grain sizes and hardness values at the stir zone (SZ), thermo-mechanically affected zone (TMAZ), heat affected zone (HAZ) and on the base materials (BM) of the samples. The reinforced FSP metal matrix composite (MMC) showed an 81.26% increase in the micro-hardness value (HV) compared to the base metal. Further on analysing the microstructures, the reinforced FSP composite showed a 65.20% reduction in grain size. Moreover, the Heat-Treated sample showed an increase in the micro-hardness value by 99.8%.

Study on Microstructure Evolution and Strengthening and Toughening of Friction Stir Processed AA6082-4%Al3Zr In-Situ Composites

Study on Corrosion Performance of Friction Stir Processed AA6082-4 wt.% Al3Zr In Situ Composites

Effect of Rotational Speed on Microstructure and Properties of Al‐Based Composite Reinforced with High‐Entropy‐Alloy Particles Fabricated by Friction Stir Processing

Effect of rotational speed on friction stir welding microstructure and properties of cast and rolled (ZrB2 + Al3Zr) particle-reinforced aluminum matrix composites

Microstructure and Mechanical Properties of Ultrahigh‐Speed Friction‐Stir‐Welded Joints of in Situ Al3Zr Particle‐Reinforced Aluminum Matrix Composite Sheets

Microstructure, hardness, and wear resistance of AA5083/Ti3SiC2 composites fabricated via friction stir processing

Fabrication of in Situ Carbon Fiber/aluminum Composites Via Friction Stir Processing: Evaluation of Microstructural, Mechanical and Tribological Behaviors

Microstructure and Mechanical Properties of Ultrahigh‐Speed Friction‐Stir‐Welded Joints of In Situ Al 3 Zr Particle‐Reinforced Aluminum Matrix Composite Sheets

Microstructure and Properties of Al3Zr/6063Al In-situ Composite Processed by FSP

Microstructural characterization and tribological behavior of surface composites fabricated on AA7050-T7451 alloy via friction stir processing

Comparative strengthening of intermetallic compounds produced in situ by friction stir processing on different aluminum alloy matrixes

Microstructure and mechanical properties of friction stir welding joint of in-situ ZrB2/AA7085 composites

Comparative study of microstructural evolution and mechanical properties in friction stir processed, reinforced friction stir processed, and heat-treated reinforced friction stir processed Al composites

Improved Mechanical Properties in Friction Stir Processed Carbon Fiber Reinforced Aluminum Composites

Parametric Influence of Friction Stir Processing on Microstructural Evolution and Tensile Behavior of AZ31/Ti-6Al-4V Magnesium Matrix Composites

Fabrication of metal matrix composites via friction stir processing

Influence of Preheating Temperature on the Microstructure and Mechanical Properties of 6061/TA1 Composite Plates Fabricated by AFSD

Friction stir processing for tensile strength and microstructure enhancement of Lm25 aluminum alloy – 5% Sicp metal matrix composites

Impact of friction stir welding parameters and Al2TiO5 reinforcement on the mechanical, wear, and corrosion performance of dissimilar welded aluminium composite joints

Effects of Energy Input During Friction Stir Processing on Microstructures and Mechanical Properties of Aluminum/carbon Nanotubes Nanocomposites

In-Situ Al-Mg Alloy Base Composite Reinforced by Oxides and Intermetallic Compounds Resulted from Decomposition of ZrW2O8 during Multipass Friction Stir Processing