Abstract:Currently there is a growing interest in investigating aluminum alloy-based hybrid composites due to their growing importance in the automotive and aerospace sectors. To enhance the value of this field, an attempt was made to synthesize zirconium diboride (ZrB 2 ) and copper-coated short steel fiber-reinforced LM26 aluminum alloy hybrid composites using stir casting with varying weight percentages of ZrB 2 (2.5, 5, and 10wt%) and copper-coated short steel fiber (5wt% kept constant) for applications requiring a lightweight and high strength, particularly for high-temperature applications. Matrix, fiber-reinforced composite (FRC), and hybrid composite specimens were synthesized using stir casting technique with the process parameters of 750°C for pouring temperature, 10 minutes for stirring time, 650 rpm for stirring speed, and 400°C for preheating temperature of reinforcements. With the use of a wire-cut electrical discharge machine, the specimens were prepared for various tests in accordance with ASTM standards. A complete microstructural (optical microscope and scanning electron microscope) investigation and mechanical property (hardness, tensile properties, and impact strength) evaluation were carried out according to the ASTM standard to comprehend the influence of the reinforcements, and the findings were presented. The optical microscopic images clearly showed that the ZrB 2 and copper-coated short steel fiber reinforcements were uniformly distributed throughout the matrix (LM26 aluminum alloy). The Brinell hardness values increased as the reinforcements were added, reaching a maximum hardness of 152 BHN for the hybrid composite with 15wt% cumulative reinforcement, which is 35.71% higher than the matrix. Compared to matrix alloy, the composite with 15% cumulative reinforcement exhibited a maximum 38.41% improvement in ultimate tensile strength. As further reinforcement is added after 10wt%, yield strength declines to 6.36%, and for the composite with 15wt% of reinforcement, elongation gradually drops to 33.7% as compared to the matrix. The energy absorption of reinforced composites with 5wt% and 15wt% shows a similar percentage decrease of 42.86%, when compared to the matrix. However, a notable decline in ductility was identified for the composites because of the addition of strong reinforcements, while the LM26 alloy retained its ductility. Further, hybrid composites showed poor resistance to impact load due to the incorporation of hybrid reinforcements, and respective fractography showed brittle fracture. The results make it quite evident that the hybrid composites of copper-coated short steel fiber and ZrB 2 -reinforced LM26 aluminum alloy have outstanding mechanical properties, making them a good choice for use in the automobile industry as a newer material.

A damage-tolerant hybrid aluminum composite reinforced with carbon nanotube and zirconia: study of strengthening mechanisms by combined experiments and molecular dynamics simulations

Hybrid (Carbon Nanotube + Graphene Nanoplatelet)/AZ31 Composite with Simultaneously Enhanced Strength and Ductility

The enhanced mechanical properties and strain-hardening capability of CNT/Al composites achieved by heterogeneous micro-laminated architecture

Effect of Multi-Walled Carbon Nanotubes and Carbon Fiber Reinforcements on the Mechanical and Tribological Behavior of Hybrid Mg-AZ91D Nanocomposites

Magnesium Based Hybrid Nanocomposites: An Insight into Nanoparticle Effects on the Microstructure and Mechanical Properties

Investigation on Mechanical Behavior of LM26 Aluminum Alloy—ZrB2 and Copper-Coated Short Steel Fiber-Reinforced Composites Using Stir Casting Process

Ton-scale Metal–carbon Nanotube Composite: the Mechanism of Strengthening While Retaining Tensile Ductility

Dual-nanoparticulate-reinforced aluminum matrix composite materials

Strength-ductility synergy induced by high-density stacking faults in aluminum alloy composites with micro/nano hybrid reinforcements

Strength-ductility synergy in a novel carbon nanotube-high entropy alloy co-reinforced aluminum matrix composite

Investigation On Tensile Properties Of Aluminum 7075 - Silica Particles -Boron Fiber- Reinforced Hybrid Metal Matrix Composites

Toughening and strengthening of Cu-coated carbon nanotubes reinforced AZ61 magnesium matrix nanocomposites by improving interfacial bonding

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Microstructure and Mechanical Properties of Cu-CoatedCarbon-Nanotubes-Reinforced Aluminum Matrix Composites Fabricated by Ultrasonic-Assisted Casting

Synergistic effects of hybrid (SiC+TiC) nanoparticles and dynamic precipitates in the design of a high-strength magnesium matrix nanocomposite

Hybrid nanocomposites: A new route towards tougher alumina ceramics

Enhanced load transfer by designing mechanical interfacial bonding in carbon nanotube reinforced aluminum composites

Experimental Studies on Mechanical Properties of Carbon Nanotube Reinforced Aluminum 7075 Composite Material

Effect of Carbon Nanotubes as Reinforcement on the Mechanical Properties of Aluminum-Copper-Magnesium Alloy

Microstructural, Mechanical and Tribological Behaviour of NiTi/SiC/ZrO2 Reinforced Aluminium 6061 Hybrid MMCs

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles