Abstract:Aluminum in terms of electrical conductivity among all known metals ranks fourth after silver, copper and gold. The electrical conductivity of annealed aluminum is approximately 62% IACS of the electrical conductivity of annealed standard copper, which at 20 °C. is taken as 100% IACS. However, due to its low specific gravity, aluminum has a conductivity per unit mass 2 times greater than copper. This property of aluminum gives us an idea of the economic viability of using it as a material for conductors. With equal conductivity (the same length), the aluminum conductor has a cross-sectional area 60% larger than copper, and its mass is only 48% of the mass of copper. In most cases, in electrical engineering, the use of aluminum as a conductor is difficult, and often simply impossible due to its low mechanical strength. An increase in the mechanical strength of aluminum is possible due to the introduction of alloying additives, i.e. creating alloys. In such a case, the mechanical strength increases, causing a noticeable decrease in electrical conductivity. The heat capacity of the aluminum conductor alloy AlTi0.1 (Al + 0.1 wt.% Ti) with calcium in the “cooling” mode was determined from the known heat capacity of the standard aluminum sample. Equations are obtained that describe the cooling rates of specimens made from an aluminum conductor alloy AlTi0.1 with calcium and a reference. Based on the calculated values of the cooling rates of the samples, the equations for the temperature dependence of the heat capacities of the alloys and the standard were formed. The temperature dependences of changes in enthalpy, entropy, and Gibbs energy for the aluminum alloy AlTi0.1 with calcium are calculated by integrating the specific heat capacity. The heat capacity, enthalpy, and entropy of the AlTi0.1 alloy decrease with increasing calcium concentration, and increase with increasing temperature, while the value of the Gibbs energy has an inverse relationship.

Temperature Dependences of the Heat Capacity and Thermodynamic Functions of Aluminum Conducting Alloy AlTi0.1 with Strontium

Influence of calcium on specific heat capacity and changes in thermodynamic functions of aluminum conductor alloy AlTi0.1

Heat Capacity and Thermodynamic Functions of the Aluminum Alloy AlCu4.5Mg1 Alloyed with Barium

The influence of calcium addition on thermophysical properties and thermodynamic functions of aluminum alloy AlCu4.5Mg1

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

Doping Effects on Internally Coupled Seebeck Coefficient, Electrical, and Thermal Conductivities in Aluminum-Doped Tio2

The Influence of Substitutional Defects of Transition Metal Elements on the Stability and Thermal Properties of Al at Finite Temperatures: A First-Principles Study

Influence of Ti Elements on the Evolution of Microstructure, Mechanical Properties and Thermal Stability of Al-Cu Alloy

The Influence of Al–10Sr Or/ and Al–5Ti–1B on Microstructure and Mechanical Properties of Al–12Si–4Cu–2Ni–0.8 Mg Alloys

Research on High-Temperature Constitutive Relationship of Aluminum Alloy

Determination of the thermophysical properties of liquid and solid Ti–6Al–4V alloy

Effect of Ti content on microstructure and properties of Al-9.9Zn-2.6Mg-0.91Cu-0.2Zr-xTi aluminum alloy

Effect of cooling rate on solidification microstructure and mechanical properties of TiB2-containing TiAl alloy

Specific Heat Measurement of Stable and Metastable Liquid Ti–Al Alloys

Enhancing thermoelectric performance of TiO 2 via aluminum doping: Insights and applications

Effect of Temperature and Rate Treatment Parameters on the Structural Phase State and Properties of Ti2AlNb Titanium Aluminide-Based Alloy

Thermal Performance Determination of Binary Fe-Al Alloys at Elevated Temperatures

Mechanical Properties of the Al3(TiTaZrNbHf) High Entropy Intermetallic Compound: A Molecular Dynamic Study

Exploring the Thermomagnetic Behavior of Co2TiZ (Z=Al, Si, Ga, Ge, and Sn) Alloys: A Computational Study

Theoretical Prediction of Structural, Mechanical, and Thermophysical Properties of the Precipitates in 2xxx Series Aluminum Alloy