Abstract:Basalt fiber (BF) has high mechanical strength, good insulation performance and low cost. It is suitable to be used as reinforcement material in the manufacture of electrical equipment. However, the large surface inertia of basalt fiber makes it difficult to combine with the matrix material, which seriously limits its service life and application scenarios. In addition, the serious vacancy in the research of insulation properties also limits its production and application in the electrical field. Therefore, in order to solve the problem of difficult bonding between basalt fiber and resin matrix and make up for the research blank of basalt fiber composites in insulation performance, this paper provides a basalt fiber modification method—SiO2 coating, and tests the insulation and mechanical properties of the modified composite. We used nano-SiO2 coating solution to modify basalt fiber, and manufactured BF/resin composite (BFRP) by hand lay-up and hot-pressing technology, and experimentally analyzed the influence of nano-SiO2 content on the mechanical and insulation properties of the modified composite. Fourier transform infrared spectrum and scanning electron microscope analysis showed that nano-SiO2 was successfully coated on basalt fibers. Through the microdroplet debonding test, it was found that the IFSS of fiber/resin was improved by 35.15%, 72.97 and 18.9%, respectively, after the modification of the coating solution with SiO2 concentration of 0.5%, 1% and 1.5%, showing better interface properties; the single fiber tensile test found that the tensile strength of the modified fiber increased slightly. Among all composites, 1 wt% SiO2 coating modified composites showed the best comprehensive properties. The surface flashover voltage and breakdown field strength reached 13.12 kV and 33 kV/mm, respectively, which were 34.6% and 83% higher than unmodified composite. The dielectric loss is reduced to 1.43%, which is 33.8% lower than the dielectric loss (2.16%) of the untreated composite, showing better insulation ability; the tensile strength, bending strength and interlaminar shear strength were increased to 618.22 MPa, 834.74 MPa and 16.29 MPa, respectively, which were increased by 53%, 42.4% and 59.7%, compared with untreated composites. DMA and glass transition temperature showed that the modified composite had better heat resistance. TGA experiments showed that the resin content of the modified composite increased, and the internal structure of the composite became denser.

Water-soluble silane terminated polyimide coating for basalt fiber to improve its thermal resistance

Preparation and properties of silicone coated glass fiber fabrics destined for firefighters' protective clothing

Effect of Nano-SiO2 Modification on Mechanical and Insulation Properties of Basalt Fiber Reinforced Composites

Surface Modification of Basalt Fibers with Improved Reactivity, Thermal Stability, and Tensile Strength

Surface Roughening of Irradiation-Activated Basalt Fiber through In Situ Growth of SiO2: Effects on Crystallization and Properties of PP Composites

Study on the effect of film-forming agent composition on moisture and heat resistance of basalt fiber composites

Ultra low-temperature fabrication of hollow glass microspheres and polysilazane coating for enhanced thermal protection of carbon/epoxy composites

In situ growth of polysiloxane nanowires on basalt fibers and interfacial enhancement with epoxy resin

Chemical and thermal resistance of basalt fiber in inclement environments

The influences of silane coupling agents on the heat and moisture resistance of basalt fibre‐reinforced composites

Mechanical properties and water-aging resistance of glass ionomer cements reinforced with 3-aminopropyltriethoxysilane treated basalt fibers

Reinforcement of Silicon-Containing Arylacetylene/Quarts Fiber Composites by Poly(imide-Co-siloxane) Macromolecular Coupling Agent

A Water-Soluble Thermoplastic Polyamide Acid Sizing Agents for Enhancing Interfacial Properties of Carbon Fibre Reinforced Polyimide Composites

Ordered Silica Nanoparticles Grown on a Three-Dimensional Carbon Fiber Architecture Substrate with Siliconborocarbonitride Ceramic as a Thermal Barrier Coating.

Enhanced interfacial and mechanical properties of basalt fiber reinforced poly(aryl ether nitrile ketone) composites by amino-silane coupling agents

Porous polyetherimide fiber fabricated by a facile micro-extrusion foaming for high temperature thermal insulation

Flexible and thermally stable SiC fiber mats derived from electrospun boron-doped polyaluminocarbosilane precursors

Flexible porous SiZrOC ultrafine fibers for high-temperature thermal insulation

Drawing on bionics, a flexible silica fiber paper is designed with high temperature resistance and hydrophobic properties

Soluble semi-aliphatic polyimide sizing in CF/PEI composites for improving mechanical performance and hydrothermal aging resistance

Surface Treatment Effect on the Mechanical and Thermal Behavior of the Glass Fabric Reinforced Polysulfone