Abstract:Background: Fe80B20 amorphous alloys exhibit excellent soft magnetic properties, high abrasive resistance and outstanding corrosion resistance. In this work, Fe80B20 amorphous micro-fibers with HC of 3.33 Oe were firstly fabricated and the effects of annealing temperature on the structure and magnetic properties of the fibers were investigated. Methods: In this study, Fe80B20 amorphous fibers were prepared by the single roller melt-spinning method. The structures of as-spun and annealed fibers were investigated by X-ray diffractometer (XRD) (PANalytical X,Pert Power) using Cu Kα radiation. The morphology of the fibers was observed by scanning electron microscopy (SEM) (HITACHI-S4800). Differential scanning calorimetry (DSC) measurements of the fibers were performed on Mettler Toledo TGA/DSC1 device under N2 protection. Vibrating sample magnetometer (VSM, Versalab) was used to examine the magnetic properties of the fibers. The resonance behavior of the fibers was characterized by an impedance analyzer (Agilent 4294A) with a home-made copper coil. Results: The X-ray diffusion (XRD) patterns show that the fibers remain amorphous structure until the annealing temperature reaches 500°C. The differential scanning calorimetry (DSC) results show that the crystallization temperature of the fibers is 449°C. The crystallization activation energy is calculated to be 221 kJ/mol using Kissinger formula. The scanning electron microscopy (SEM) images show that a few dendrites appear at the fiber surface after annealing. The result indicates that the coercivity HC (//) and HC (⊥) slightly increases with increasing annealing temperature until 400°C, and then dramatically increases with further increasing annealing temperature which is due to significant increase in magneto-crystalline anisotropy and magneto-elastic anisotropy. The Q value firstly increases slightly when the annealing temperature rises from room temperature (RT) to 300°C, then decreases until 400°C. Eventually, the value of Q increases to ~2000 at annealing temperature of 500°C. Conclusions: In this study, Fe80B20 amorphous fibers with the diameter of 60 μm were prepared by the single roller melt-spinning method and annealed at 200°C, 300°C, 400°C, and 500°C, respectively. XRD results indicate that the fiber structure remains amorphous when the annealing temperature is below 400°C. α-Fe phase and Fe3B phase appear when the annealing temperature rises to 500°C, which is above the crystallization temperature of 449°C. The recrystallization activation energy is calculated to be 221 kJ/mol. The coercivity increases with increasing annealing temperature, which attributes to the increase of total anisotropy. All the as-spun and annealed fibers exhibit good resonance behavior for magnetostrictive sensors.

Morphologies and mechanical properties of basalt fibre processed at elevated temperature

Effects Of Elevated Temperature Treatment On Compositions And Tensile Properties Of Several Kinds Of Basalt Fibers

Mechanical Properties and Microstructures of Steel-basalt Hybrid Fibers Reinforced Cement-based Composites Exposed to High Temperatures

Correlation Between Macroscopic Properties and Microscopic Pore Structure in Steel-Basalt Hybrid Fibers Reinforced Cementitious Composites Subjected to Elevated Temperatures

Structural Classification of Basalt FRP at High Temperatures

Surface Modification of Basalt Fibers with Improved Reactivity, Thermal Stability, and Tensile Strength

Effects of annealing on the structure and magnetic properties of Fe80B20 magnetostrictive fibers

Influence of Basalt Fiber on the Mechanical Properties and Deformation Failure of Concrete after High Temperature

Effect of heat‐treatment on the microstructure and room‐temperature mechanical properties of alumina–silica fiber

Effects of Annealing Temperature on the Structures, Ferroelectric and Magnetic Properties of Aurivillius Bi5ti3feo15 Polycrystalline Films

Influence of fabric structures and temperature on the mechanical properties of quartz braids

Thermal properties, microstructure analysis, and environmental benefits of basalt fiber reinforced concrete

Evolution of microstructures and thermal properties with heat treatment for absorbing, emitting and scattering fibrous medium

Microstructure evolution and mechanical behavior of a mullite fiber heat‐treated from 1100 to 1300°C

Effects of raw material homogenization on the structure of basalt melt and performance of fibers

Surface Roughening of Irradiation-Activated Basalt Fiber through In Situ Growth of SiO2: Effects on Crystallization and Properties of PP Composites

Petrographic Investigation into the Influence of Chopped Basalt Fibers on the Microstructure of Portland Cement Mortars at Elevated Temperatures

Mechanism Analysis on Tensile Fracture Properties of Heterogeneous BFLAC at Cryogenic Temperature: Experimental Investigation and Mesoscale Simulation

Crystallization Kinetics of Modified Basalt Glass

Effect of melt homogenization on the structure and properties of zirconium-rich basalt fibers

Mechanical properties of polyvinyl alcohol-basalt hybrid fiber engineered cementitious composites with impact of elevated temperatures