Abstract:The effects of wet mixing and traditional mixing on the properties of radial-orientation basalt fiber-reinforced rubber products were studied through experiments. The results show that compared with traditional mixing, the basalt fibers under the wet mixing conditions can more effectively enhance the physical and mechanical properties of composites. The properties of the composites, such as carbon black dispersion, filler dispersion, rolling resistance and wet-sliding resistance, were the best after the latex and carbon black were premixed and then mixed by a mixer. Through extrusion experiments with the developed short-fiber radial-orientation die, it can be found that the fluidity of composites after extrusion is enhanced. Through analysis utilizing an electron microscope, it is shown that when the BFs added with KH550 (3-Aminopropyltriethoxysilane) were modified by KH560 ((3-Glycidyloxypropyl)trimethoxysilane), the interface layers of BF (basalt fiber)–KH560–NR and BF–KH550–NR were formed, which improves the adhesion between BFs and the rubber matrix. Qualitative characterization experiments on the orientation direction of the vulcanized composites were carried out through the experiments; that is, the qualitative characterization experiments on the segmented cutting and vulcanization of the composites in the radial direction showed that the short-fiber radial-orientation die could greatly improve the radial orientation degree of the short fibers in the radial direction. After adding KH560, the performance of the composites reinforced by the short fibers was improved to a certain extent compared with those without KH560. By adding DZ (N,N-Dicyclohexyl-2-benzothiazolsulfene amide) and CTP(cytidine triphosphate disodium) into the vulcanization system, the curing process of compounds in mixing and extrusion was delayed and the scorching resistance of short-fiber-reinforced composites was enhanced. Under the same conditions, the properties of the compounds after extrusion were greatly improved compared with those without extrusion.

Effects of raw material homogenization on the structure of basalt melt and performance of fibers

Effect of melt homogenization on the structure and properties of zirconium-rich basalt fibers

Fabrication of Homogeneous Mullite-Based Fiber Porous Ceramics with High Strength and Porosity

Crystallization Kinetics of Modified Basalt Glass

Effects Of Elevated Temperature Treatment On Compositions And Tensile Properties Of Several Kinds Of Basalt Fibers

A Brillouin Scattering Study of Hydrous Basaltic Glasses: the Effect of H2o on Their Elastic Behavior and Implications for the Densities of Basaltic Melts

Mechanical Properties and Microstructures of Steel-basalt Hybrid Fibers Reinforced Cement-based Composites Exposed to High Temperatures

Morphologies and mechanical properties of basalt fibre processed at elevated temperature

Effects of Elevated Temperatures on the Mechanical Properties of Basalt Fibers and BFRP Plates

Effect of Basalt Fiber Diameter on the Properties of Asphalt Mastic and Asphalt Mixture

Resistance of basalt fibers to elevated temperatures and water or alkaline solution immersion

Mechanical and Thermal Properties of Basalt Fiber Reinforced Poly(butylene Succinate) Composites

Surface Roughening of Irradiation-Activated Basalt Fiber through In Situ Growth of SiO2: Effects on Crystallization and Properties of PP Composites

Effect of Wet Mixing on Properties of Radial-Orientation Basalt Fiber-Reinforced Rubber Compounds

Homogenization heat treatment of Mg-9.0Y-3.0MM-0.6Zr alloy

Effects of Radiation-Induced Crosslinking on Thermal and Mechanical Properties of Poly(lactic Acid) Composites Reinforced by Basalt Fiber

Microstructures evolution of nano TiB2/7050Al composite during homogenization

A morphological study of mullite long fiber prepared using polyvinyl butyral as spinning aids

Mechanical and Interfacial Properties of Bare Basalt Fiber

Effect of homogenization temperature on microstructure and mechanical properties of low-carbon high-boron cast steel

Physical and High Temperature Properties of Basalt Fiber-Reinforced Geopolymer Foam with Hollow Microspheres