Abstract:: ENE-FARM type S equipped with solid oxide fuel cell (SOFC) stack has been commercialized since 2012. To further expand the market of ENE-FARM type S, higher electrical efficiency, higher durability, and lower cost of SOFC stack are required. A coating on a SOFC metallic interconnector is the key technology for the long-term durability of SOFC. In this research, we achieved a significant reduction in resistance and improved durability by improving the highly mass-producible electrodeposition coating method, one of the ceramic coating methods for the SOFC metallic interconnector. Furthermore, the cost of metallic interconnector has been reduced using commodity stainless steel due to its high durability. The SOFC stack of the 2016 model equipped with the electrodeposition coating on the commodity ferritic stainless steel had higher performance and durability than the 2012 model, even if the current density was increased approximately 1.5 times. The electrodeposition coating on commodity ferritic stainless steel has been commercialized and installed in the 2016 and 2020 models of ENE-FARM type S. electrodeposition the electrodeposition the SOFC interconnector coating. specimen was synthesized via conventional solid-state reaction. Specimens were obtained from a mixture of raw powders of ZnO, Mn 2 O 3 , and Co 3 O 4 . Finally, powders were pressed into a rectangular shape before sintering at 1273 K for 2 h in air. The specimens obtained were characterized using a four-probe DC conductivity measurement at 873–1073 K in air. Figure shows the total electrical conductivity of ZnMn x Co 2- x O 4 ( x = 0.0–2.0) specimens functions of Mn and Co The electrical 1.0. ZnMn x Co 2- x O ratio 1/1. Co 2- x O 4 x = 0.0–2.0)

Technical Development of The Electrochemical Society of Japan (Tanahashi Award) Development of Electrodeposition Coating for SOFC Interconnector

Interface Design Development for High Durability of SOFC Interconnectors Using Electrodeposition Coating

Preparation of a nickel-cobalt-zinc alloy coating as SOFC connection material in deep eutectic solvent

Thermally Sprayed MCO/FeCr24 Interconnector with Improved Stability for Tubular Segmented-in-series SOFCs

Progress in SOFC Metallic Interconnect Coating

Ni–Co/ZrO2 Composite Coatings via Electroless Plating on Crofer 22APU for SOFC Interconnect Applications: Oxidation and Chromium Vaporization Behavior

Influences of Composite Electrodeposition Parameters on the Properties of Ni-Doped Co-Mn Composite Spinel Coatings

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

Performance of stainless steel interconnects with (Mn,Co)3O4-Based coating for solid oxide electrolysis

Fe doped Ni–Co alloy by electroplating as protective coating for solid oxide fuel cell interconnect application

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Development and Application of HVOF Sprayed Spinel Protective Coating for SOFC Interconnects

Dense Mn1.5Co1.5O4 coatings with excellent long-term stability and electrical performance under the SOFC cathode environment

Influence of Electrophoretic Deposition (EPD) Voltage on SOFC Interconnect Morphology

The electrical property of MnCo2O4 and its application for SUS 430 metallic interconnect

Fabrication of Mn–Co Alloys Electrodeposited on AISI 430 Ferritic Stainless Steel for SOFC Interconnect Applications

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

Plasma spray coating on interconnector toward promoted solid oxide fuel cells and solid oxide electrolysis cells

Effect of Rare Earth Y and Metal X (Co, Mn, Ni, Cu) Elements on Cr Diffusion Behavior of SOFC Metallic Interconnect

Protective coating based on manganese–copper oxide for solid oxide fuel cell interconnects: Plasma spray coating and performance evaluation

Effect of MnCoNiFeCu Alloy on Oxidation Behavior and Electrical Performance of AISI 441 for SOFC Interconnect Application