Abstract:Characteristics of dielectric significantly influence machining performance of micro electrical discharge machining (EDM). A high material removal rate and large tool wear are obtained in micro EDM in liquid dielectric. Tool wear in gas dielectric is small, but the material removal rate is extremely low. In previous study, it was found that micro EDM in atmospheric pressure nitrogen plasma jet (APPJ) obtained a higher material removal rate than that in gas dielectric. However, material removal rate is still much lower than in liquid dielectric. To improve the machining performance of micro EDM in APPJ, this paper proposes micro EDM in APPJ assisted with coaxial mist (APPJ + mist). Effects of both flow rate of mist and discharge pulse energy on the critical breakdown distance, material removal rate, tool electrode wear ratio, surface roughness and profile are investigated. Experiments in nitrogen with coaxial mist (nitrogen + mist), deionized water and pure mist are also conducted for comparison. Experimental results indicate that critical breakdown distances in APPJ + mist, nitrogen + mist and mist are larger than in APPJ and deionized water. To understand the effect of misted droplets on critical breakdown distance, electric field intensity of the gap in deionized water and mist were simulated. Theoretical analysis reveals that electric field intensity on the surface of water droplet is much larger than that of tool electrode rim, resulting in the easy breakdown of gap with misted droplet. Material removal rate increases from 200 mu m(3)/s (without mist) to 1252 mu m(3)/s (with 5 mL/min mist) in APPJ in the case of open voltage of 100 V and capacitance of 8200 pF, which is higher than material removal rate in deionized water (1096 mu m(3)/s) under the same discharge parameters. There is almost no tool electrode wear in APPJ + mist. The surface roughness of machined groove in APPJ + mist is 538 nm much lower than that in deionized water (672 nm), nitrogen + mist (627 nm) or pure mist (691 nm). Straighter side walls and flatter bottoms of micro grooves were obtained in APPJ + mist and nitrogen + mist than those in deionized water and mist. A micro cavity is also generated by using the proposed method without compensation of tool electrode wear.

Discharge Characteristics and Mechanisms of Electrolytic Discharge Processing by Jet Mask

Experimental Study of an Electrostatic Field–induced Electrolyte Jet Electrical Discharge Machining Process

Mechanism Analysis of Discharge Energy in the Electrostatic-Field-Induced Electrolyte Jet Micro-EDM

Experimental Investigation of the Governing Parameters of the Electrostatic Field–induced Electrolyte Jet Micro Electrical Discharge Machining on the Silicon Wafer

Intensive Study on the Electrostatic Field Induced Electrolyte Jet Micro Electrical Discharge Machining

The Tool Electrode Investigation of Electrostatic Field-Induced Electrolyte Jet (E-Jet) Electrical Discharge Machining

Research on Electrostatic Field-Induced Discharge Energy in Conventional Micro EDM

Chain discharging behavior induced by gas film expansion and its influence on the electrochemical discharge machining (ECDM) process

Investigation on Modified Jet Electrochemical Machining of Micro-Channel

Investigation of the Material Removal Mechanism in Electrochemical Discharge Drilling Using a High-Speed Rotating Helical Tool-Electrode

Experimental and Numerical Investigations on Fabrication of Surface Microstructures Using Mask Electrolyte Jet Machining and Duckbill Nozzle

Insights into the high-speed electrochemical discharge drilling for film cooling hole: Machining phenomena, morphological evolution, and visualize simulation

An Analysis of the Discharge Mechanism in Electrochemical Discharge Machining of Particulate Reinforced Metal Matrix Composites

The Investigation of Discharge Restriction Mechanism of the Floating Workpiece Based Electrostatic Field-Induced Electrolyte Jet (E-Jet) Edm

Jet Electrochemical Micromachining Of Micro-Grooves With Conductive-Masked Porous Cathode

High-speed Micro Electrical Discharge Machining with Fine Surface Quality in Atmospheric Pressure Nitrogen Plasma Jet

Electrical Discharge Machining In Jetted Mist

Fabrication of Surface Microstructures by Mask Electrolyte Jet Machining

Research on Submersed Gas-jetting Electrical Discharge Milling

The Study on Mechanism of Field Induced Jet Micro EDM

Research on Processing Law of Micro-EDD in Air