Abstract:Suitable compatibilizers are essential to prepare immiscible polymer blends with stable co‐continuous morphologies. From the thermodynamic point of view, such compatibilizer should not only reduce the interfacial tension, but also promote the formation of flat interface between different phases. Meanwhile, it must not hinder the coalescence of dispersed phase. Therefore, asymmetric structures are required for those block or graft copolymer compatibilizers. However, from the kinetic point of view, copolymers with asymmetric structures are prone to be dragged out from the interface and form micelles in one phase under the processing conditions, which will lose their compatibilization effects. The balance between such thermodynamic and kinetic factors remains unclear. In this paper, the relationship between the morphology of the compatibilized polystyrene/nylon 6/styrene‐maleic anhydride copolymers (PS/PA6/SMA) immiscible polymer blends and the structures of the in‐situ formed SMA‐g‐PA6 graft copolymers as well as the processing conditions are studied. Two kinds of SMA are used as compatibilizers: SMA28 (Mw = 110,000 g/mol, MAH content 28 wt.%) and SMA11 (Mw = 110,000 g/mol, MAH content 11 wt.%). After melt blending with PA6 into an internal mixer, the in‐situ formed copolymer SMA28‐g‐PA6 has an average four PA6 side chains grafted on one SMA backbone, while that of SMA11‐g‐PA6 has only one PA6 side chain. Dissipative particle dynamics (DPD) simulation results indicate that both SMA28‐g‐PA6 copolymer and PS/PA6/SMA28 blends tend to form co‐continuous structure, while SMA11‐g‐PA6 copolymer and PS/PA6/SMA11 blends form sea‐island morphologies. However, these results are confirmed experimentally only at relatively low rotor speed of the internal mixer (60 rpm). When the rotor speed of the mixer is higher (105 rpm), sea‐island morphologies are obtained in PS/PA6/SMA28 blends and co‐continuous ones are found in PS/PA6/SMA11 systems. These results indicate that higher shear stress will favor to elongate the minor phase domains and form flat interfaces, which is benefit for the formation of co‐continuous morphologies; meanwhile, high shear stress may pull the graft copolymers with asymmetric structures (SMA28‐g‐PA6) out from the interface of PS and PA6 and induce the formation of sea island morphologies. This article is protected by copyright. All rights reserved

The conformational statistics of amphiphilic polymers with distinct topological structures at the interface between two phases

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Effect of Mixing Protocol on Compatibilized Polymer Blend Morphology

Dissipative Particle Dynamics Study on Interfacial Properties of Symmetric Ternary Polymeric Blends

Sequential Mesoscale Approach for Determining the Effects of the Addition of A Block Copolymer Compatibilizer on the Mechanical Properties of Polymer Blends

Enhancing Polymer Blend Compatibility with Linear and Complex Star Copolymer Architectures: A Monte Carlo Simulation Study with the Bond Fluctuation Model

Dissipative Particle Dynamics Study on Interfacial Properties of Ternary H-Shaped Copolymer–Homopolymer Blends

Role of compatibilizer in multicomponent polymer mixtures under shear flow

Effect of composition distribution on miscibility and co-crystallization phenomena in the blends of low density polyethylene with conventional and metallocene-based ethylene–butene copolymers

Distinctive Morphology Modifiers for Polymer Blends: Roles of Asymmetric Janus Nanoparticles During Phase Separation.

Dual Effects of Compatibilizer on the Formation of Oriented Ribbon-Like Dispersed Phase Domains in Polystyrene/polyamide 6 Blends

Tuning phase separation morphology in blend thin films using well-defined linear (multi)block copolymers

Compatibilization and morphology development of immiscible ternary polymer blends

Structure Development from Simultaneous Phase Separation and Crystallization of Metallocene Polyolefin Blends.

Effect of Phase Morphology on the Reactive Blending

Relationship Between The Co‐Continuous Morphology of Immiscible Polymer Blends and the Structure of An In Situ Formed Graft Copolymer

Influence of Block Lengths and Symmetries of Block Copolymers on Phase Behavior of Polymer A/polymer B/block Copolymer Ternary Blends

Monte Carlo Simulation of Phase Behavior of Polymer Blends with Special Interactions

Phase Equilibria, Morphologies of Microphase Separation, and Interfacial Structures of Polymer Systems Studied by Equations of State

Molecular Dynamics Simulation of Miscibility in Several Polymer Blends

A Dynamic Mechanical Analysis on the Compatibilization Effect of Two Different Polymer Waste-Based Compatibilizers in the Fifty/Fifty Polypropylene/Polyamide 6 Blend