Abstract:The study examines the dimensional changes of compatibilizer copolymers with varying topological structures at the interface of a binary blend system. It delineates the scaling exponent between the size of these compatibilizer copolymers and their respective chain lengths and analyzes the factors that contribute to the variation in the scaling exponent. The distribution and conformational state of compatibilizer polymers at the interface between two phases are challenging to obtain in detail through experimental research due to spatial scale limitations. This paper employs dissipative particle dynamics simulation to statistically analyze the size variations of compatibilizer copolymers at the interface of a binary blend system. The study examines the impact of factors such as the chain length of blended homopolymers, the topological structure of the compatibilizer and component interactions on the size distribution of compatibilizer copolymers at the interface. The scaling exponent between the size of the compatibilizer copolymers and their chain length is determined and compared with theoretical values under melt conditions. The reasons for the variation in the scaling exponent are analyzed, providing theoretical supplementation for the distribution, size changes and compatibilization effects of compatibilizers during the blend modification process. The results reveal discrepancies between the scaling exponent of chain size and chain length at the interface and theoretical values, analyze the significant impact of compatibilizer copolymer topological structure on the scaling exponent and present the influence of the component interaction parameter α on the scaling exponent's variation pattern. The simulation outcomes offer theoretical support for the design and selection of compatibilizers in a blend system. © 2024 Society of Chemical Industry.

Dissipative Particle Dynamics Study on Interfacial Properties of Ternary H-Shaped Copolymer–Homopolymer Blends

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Dissipative Particle Dynamics Study on Interfacial Properties of Symmetric Ternary Polymeric Blends

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Effects of Repulsion Parameter and Chain Length of Homopolymers on Interfacial Properties of An/Ax/2BxAx/2/Bm Blends: A DPD Simulation Study

Tuning polymer blends to cocontinuous morphology by asymmetric diblock copolymers as the surfactants

Phase Behavior of Ternary Homopolymer/Gradient Copolymer Blends

Influence of Block Lengths and Symmetries of Block Copolymers on Phase Behavior of Polymer A/polymer B/block Copolymer Ternary Blends

Solvent-Induced Morphology of the Binary Mixture of Diblock Copolymer in Thin Film: the Block Length and Composition Dependence of Morphology

Compatibility Of Triblock Copolymers In An A/B/Copolymer Ternary Mixture

Enhancing Polymer Blend Compatibility with Linear and Complex Star Copolymer Architectures: A Monte Carlo Simulation Study with the Bond Fluctuation Model

Sequential Mesoscale Approach for Determining the Effects of the Addition of A Block Copolymer Compatibilizer on the Mechanical Properties of Polymer Blends

Which is More Efficient As Compatibilizer: Di-block or Multiblock Copolymer?

The conformational statistics of amphiphilic polymers with distinct topological structures at the interface between two phases

Morphologies of Diblock Copolymer/Homopolymer Blend Films

Compatibilization And Toughening Of Immiscible Ternary Blends Of Polyamide 6, Polypropylene (Or A Propylene-Ethylene Copolymer), And Polystyrene

Nucleation in Binary Polymer Blends: Effects of Adding Diblock Copolymers

Tuning phase separation morphology in blend thin films using well-defined linear (multi)block copolymers

Distinctive Morphology Modifiers for Polymer Blends: Roles of Asymmetric Janus Nanoparticles During Phase Separation.

Interfacial Interaction Analysis of Blends of Poly(vinylidene Fluoride) and Poly(ethylene–butylacrylate–glycidyl Methacrylate) Compatibilized by Poly(butylene Succinate): Morphologies, Rheological Behavior, and Mechanical Properties

Interfacial Engineering of Polymer Blend with Janus Particle As Compatibilizer