Abstract:High-entropy alloys, a new class of metallic materials, exhibit excellent mechanical properties at high temperatures. In spite of the worldwide interest, the underlying mechanisms for temperature dependence of mechanical properties of these alloys remain poorly understood. Here, we systemically investigate the mechanical behaviors and properties of Al 1.2 CrFeCoNi (comprising a body-centered cubic phase) and Al 0.3 CrFeCoNi (comprising a face-centered cubic phase) single-crystal micropillars with three orientations ([100], [110], and [111]) at temperatures varying from 300 to 675 K by using in situ compression of micropillars inside a scanning electron microscope. The results show that the yield stresses of Al 1.2 CrFeCoNi micropillars are insensitive to temperature changes, and their flow stresses and work hardening rates increase slightly with increasing temperature from 300 to 550 K, which differs from the typical temperature dependence of yield/flow stresses in metals and alloys. In contrast, Al 0.3 CrFeCoNi micropillars exhibit typical thermal softening. Furthermore, it is found that the Al 1.2 CrFeCoNi micropillars exhibit a transition from homogenous deformation to localized deformation at a critical temperature, while the Al 0.3 CrFeCoNi micropillars always maintain a well-distributed and fine slip deformation. Detailed transmission electron microscopy analyses reveal that dynamic recrystallization (involving dislocation tangles, and formation of dislocation cell structures and sub-grains) plays a key role in the observed temperature insensitivity of the yield stress and increasing flow stress (and work hardening rate) with increasing temperature in the Al 1.2 CrFeCoNi micropillars, and that thermally activated dislocation slip leads to thermal softening of the Al 0.3 CrFeCoNi micropillars. The differences in deformation modes and temperature dependence of the mechanical properties between Al 1.2 CrFeCoNi and Al 0.3 CrFeCoNi essentially originate from the differences in dislocation activities and slip systems since the two alloys adopt different phases. Our findings provide key insights in the temperature dependence of mechanical properties and deformation behaviors of high-entropy alloys with body-centered cubic and face-centered cubic phases.

Crystallization Toughening of Fe-Based Amorphous Alloys Under Strain–Heat Coupling Effect

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

The Crystallization Kinetics Study of Finemet-Co Amorphous Alloys

Elemental partitioning-mediated crystalline-to-amorphous phase transformation under quasi-static deformation

Orientation dependence of the nanocrystallization and magnetic behavior during annealing of the FINEMET alloy

The effect of changes in Al-based amorphous phase structure on structure forming upon crystallization

Effect of annealing treatment on microstructural evolution and compressive behavior of Al0.5CrFeNi2.5Si0.25 high-entropy alloy

Temperature effect on tensile behavior of an interstitial high entropy alloy: Crystal plasticity modeling

Toughness under Different Rolling Processes in Ultra Purified Fe–17wt% Cr Alloy Steels

Effect of Stress-Temperature Coupling on Gradient Alloying Induced by Punching Severe Deformation

Effect of Stress on Crystallization Behavior in a Fe-based Amorphous Ribbon: an in Situ Synchrotron Radiation X-ray Diffraction Study

The Deformation Behavior and Microstructure Evolution of a Mn- and Cr-Containing Al-Mg-Si-Cu Alloy During Hot Compression and Subsequent Heat Treatment

Annealing-induced multi-heterogeneous microstructure strengthening in FeCoCrNiMo 0.2 high-entropy alloys

In-situ study of room temperature tensile deformation of a CrMnFeCoNi high-entropy alloy

Unraveling the Deformation Behavior of the Fe45Co25Ni10V20 High Entropy Alloy

Dynamic recrystallization-induced temperature insensitivity of yield stress in single-crystal Al 1.2 CrFeCoNi micropillars

Crystallization behavior, soft magnetic properties and good bending ductility of high Fe content FeSiBCuPC alloys induced by composition design

Effect of Deformation Parameters on Microstructure Evolution of FGH4113A Powder Metallurgy Superalloy

Inhibiting cracking and improving strength for additive manufactured Al x CoCrFeNi high entropy alloy via changing crystal structure from BCC-to-FCC

Effect of Cold Deformation and Heat Treatment on the Microstructure and Mechanical Behavior of High Entropy Alloy CuCrFeNi2Al0.5