Abstract:The aluminum dross (AD), which causes numerous problems of its management and disposal to environment is a useful resource to extract alumina. This study explains a novel process to extract highly pure alumina (Al2O3) from AD at a high extraction rate without producing the residues and exhaust gases. An experimental set up was designed to perform the grinding of AD for the decomposition of aluminum nitride (AlN) and the removal of salts. Thereby, the desalted dross was used to detect the optimum alkaline (NaOH) calcination parameters and leaching conditions, as well as the dissolution kinetics of alumina and silica. The leaching residues were used to produce Ettringite mineral with calcium-based compounds (including CaO and CaSO4) to avoid the problems of solid waste disposal from the leaching process. Moreover, to purify the alumina, slightly soluble CaSO4 was added in leaching solution to precipitate silicate and the optimum additive/solution ratio (g/mL) was determined. The aluminum hydroxide (Al(OH)3), precipitated after the carbonization was calcinated at 900.0 °C for 2 h to produce γ-alumina. The morphological and mineralogical characterizations of AD, γ-Al2O3 and the synthesized Ettringite mineral were studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and X-ray fluorescence (XRF). It was observed that activation temperature of 1000.0 °C, Na2O/Al2O3 molar ratio of 1.4, leaching temperature of 60.0 °C, leaching time of 40.0 min, and the leaching liquid/solid ratio (mL/g) of 25/1 were the optimal parameter conditions to extract alumina with the extraction rate at 86.7% and purity of more than 98%. The results of leaching kinetics' study showed that the dissolution of alumina and silica were both controlled by layer diffusion process with the apparent activation energy of 11.4010 kJ·mol-1 and 2.0556 kJ·mol-1, respectively.

Improved CFD modeling of full dissolution of alumina particles in aluminum electrolysis cells considering agglomerate formation

Modelling the formation and dissolution behavior of alumina agglomerate in the cryolite

Improved CFD Modeling of the Whole-Cell Side Ledge Behavior in Aluminum Electrolysis Cell

Modeling and Parametric Study of Spent Refractory Material Dissolution in an Aluminum Reduction Cell

Flotation of Alumina on the Surface of the Electrolyte in an Aluminum Electrolysis Cell

Mass- and Heat Transfer During Dissolution of Alumina

Structural reconstruction and thermophysical properties of alumina agglomerate based on QSGS calculation

Simulation of aluminium electrodeposition on complex geometry: Influence of input parameters and electrodeposition conditions

Study on the dissolution of aluminium carbide formed on the graphite cathode in aluminium electrolysis

Impurity Behavior in Aluminum Extraction by Low-Temperature Molten Salt Electrolysis

Dissolution of Alumina from Fly Ash Sintered Clinker

Alumina Solubility and Dissolution Rate in NaF-KF-AlF3-LiF-CaF2 Low-Temperature Electrolyte

Properties and composition of the spent electrolyte for premium circulation mediated by Al-air batteries.

Influences of various aluminum accumulation sump designs on thermal stress distribution in drained aluminum reduction cell

Enhancing Efficiency in Alkaline Electrolysis Cells: Optimizing Flow Channels through Multiphase Computational Fluid Dynamics Modeling

Fully-Coupled Electric-Thermal-Flow Modeling and Investigation of Dynamic Thermal-Ledge Behavior in Aluminum Electrolysis Cell

Extraction of alumina from aluminum dross by a non-hazardous alkaline sintering process: Dissolution kinetics of alumina and silica from calcined materials

Enhancing activated sludge dewatering performance: Impact of alum dosage on dehydration characteristics and microstructure

Modulating Aluminum Solvation with Ionic Liquids for Improved Aqueous-Based Aluminum-Ion Batteries

A cleaner electrolysis process to recover alumina from synthetic sulfuric acid leachate of coal fly ash

An ab initio molecular dynamics investigation of the behaviour of amorphous substances in anodic aluminium oxide under electric field