Abstract:A novel amperometric NO2 sensor was fabricated using a nanostructured La0.8Sr0.2MnO3-delta (nano-LSM) sensing electrode (SE) and a Ce0.8Gd0.2O1.9 (CGO) electrolyte. The focus of this study was to extend the electrochemical active site at the three-phase boundary (TPB) and reduce the interfacial resistance by introducing a hybrid ion/ electron conducting porous layer (CGO +LSM) between the SE and the electrolyte. By adjusting the amount of LSM, the effects of the LSM/CGO ratio on the microstructure and sensitivity of the sensor were investigated. The results showed that the addition of LSM did not change the porous structure of the CGO porous skeleton, but the number of pores decreased with the increase of LSM addition, while the size of pores increased with increasing the amount of LSM added. The nano-LSM was prepared in-situ into the porous skeleton by the impregnation technology, which was highly dispersed in the porous skeleton, having reached the bottom of the porous layer with a particle size of less than 100 nm. The sensor with a mixed conductor as the porous layer effectively improved the sensitivity of the sensor. Analysis by electrochemical impedance spectroscopy (EIS) and the distribution of relaxation techniques (DRT) demonstrated that the addition of the electronic conductor LSM into the CGO porous layer significantly reduced the diffusion resistance of the sensor and enhanced the oxygen exchange performance, thus improving the response performance of the sensor. The sensor with 30wt% LSM/CGO porous layer had good reproducibility and excellent stability. The sensor had good anti-interference performance against co-existing CH4, CO2, H2, NO, and NH3, with good linearity between sensor response values and NO2 concentrations over different O2 concentrations and relative humidity (RH).

Improving the stability of an amperometric ammonia sensor based on BaZr0.8Y0.2O3-δ electrolyte with a volatile B2O3 sintering additive

Increasing the Sensitivity of an Amperometric, YSZ-based Total-Nox Sensor by Opening the Gas Diffusion Pathways in a Porous La0.8Sr0.2MnO3 Electrode

Amperometric Ammonia Sensors for Low Detection Limit with BaZr(1-x)YxO3-δ Proton Electrolytes

A stable and easily sintering BaCeO3-based proton-conductive electrolyte

An Amperometric High-Temperature Ammonia Sensor Based on a Baco0.4fe0.4zr0.1y0.1o3-Δ Triple Conductor

Improvement of Al 3+ ion conductivity by F doping of (Al 0.2 Zr 0.8 ) 4/3.8 NbP 3 O 12 solid electrolyte for mixed potential NH 3 sensors

Mixed-Potential Ammonia Sensor Based on a Dense Yttria-Stabilized Zirconia Film Manufactured at Room Temperature by Powder Aerosol Deposition

Sensitivity and selectivity enhancement of the YSZ-based mixed-potential ammonia sensors with flame-spray-made double-sensing electrodes

A Mixed-Potential Type NH <sub>3</sub> Sensor Based on Spinel Zn <sub>2</sub>SnO <sub>4</sub> Sensing Electrode

A mixed-potential type NH3 sensors based on spinel Zn2SnO4 sensing electrode

Mixed potential NH<sub>3</sub> sensor based on La<sub>9.95</sub>K<sub>0.05</sub>Si<sub>5</sub>Al<sub>1</sub>O<sub>26.45 </sub> electrolyte and Ag doped BiVO<sub>4</sub> sensing electrode

Enhanced Sensing Performance of Mixed Potential Ammonia Gas Sensor Based on Bi0.95Ni0.05VO3.975 by Silver

Enhanced Sensing Performance of the Amperometric NO2 Sensor by Use of a Mixed Conductive Porous Layer

BaZr0.8Y0.2O3−δ electrolyte with and without ZnO sintering aid: Preparation and characterization

Enhancing Ammonia Sensing Performance of Ag 2 MoO 4 -based Mixed-Potential Sensor by Introducing Ionic and Electronic Conductance

Potentiometric NO2 Sensors Based on Thin Stabilized Zirconia Electrolytes and Asymmetric (La0.8Sr0.2)0.95MnO3 Electrodes

Effects of Sintering Temperature on the NH3 Sensing Properties of Mg2Cu0.25Fe1O3.75 Electrode for YSZ-based Potentiometric NH3 Sensor

A Highly Sensitive and Selective NH<sub>3</sub> Sensor Based on a Spherical In<sub>2</sub>O<sub>3</sub>-Sensing Electrode Prepared Using the Hydrothermal Method

Synergistic Enhancement on the Sensing Performance of Mixed Potential NH3 Sensors by Fe and Mo Codoping into BiVO4

A novel amperometric hydrogen sensor based on nano-structured ZnO sensing electrode and CaZr 0.9In 0.1O 3-δ electrolyte

The effects of Cu-content on Mg2CuxFe1O3.5+x electrodes for YSZ-based mixed-potential type NH3 sensors