Abstract:Abstract Silicon and molybdenum ( SiMo ) ductile iron is commonly used for exhaust manifolds because these components experience thermal cycling in oxidizing environment, which requires resistance to fatigue during transient thermomechanical loads. Previous studies have demonstrated that alloying elements, such as Al , to SiMo ductile iron reduces the amount of surface degradation during static high-temperature exposure. However, deterioration of sphericity of the graphite nodules and a decrease in ductility could affect the tendency of cracking during thermal cycling. In this article, the effect of Al alloying on static and transient thermomechanical behavior of SiMo ductile iron was investigated to optimize the amount of Al alloying. A thermodynamic approach was used to confirm the effect of the Al alloying on the phase transformations in two SiMo cast irons, alloyed by 1.8% Al and 3% Al . These two alloys were cast in a laboratory along with the baseline SiMo ductile iron. Several experimental methods were used to evaluate the dimensional stability, physical properties, static oxidation, and failure resistance during constrained thermal cycling testing to compare their high-temperature capability. Experimental results verified that Al alloying increases the temperature range and decreases volume change during eutectoid transformation, which together with enhancement of oxidation protection improved the dimensional stability. Thermocycling tests showed that the number of cycles to failure depends on the amount of Al alloying and the applied high-temperature exposure during each cycle. SEM/EDX, high-resolution TEM and μCT analysis were used to verify the mechanism resulting from the Al alloying protection. It was shown that an optimal level of Al alloying for balancing oxidation and thermal cracking resistance depends on thermomechanical conditions of application.

Reaction Behavior at the Contact Interfaces between High-Manganese Cast Steel or High-Manganese Spheroidal Graphite Cast Iron and Molten Aluminum Alloys

Effect of Mg Content on the Shear Strength of Al-Si-Mg and Al-Si-Cu Alloys at Elevated Temperatures

Effects of Manganese and Heat Treatment on Mechanical Properties in Spheroidal Graphite Cast Iron

Effect of Alloying Elements on Solidification Cracking Susceptibility of High Manganese Austenitic Steel

Improving High-Temperature Performance of High Si-Alloyed Ductile Iron by Altering Additions

Improvement of High-Temperature Performance of High Si SGI by Al Alloying and Optimizing Microstructural Dispersity

Effect of melting temperature on microstructural evolutions, behavior and corrosion morphology of Hadfield austenitic manganese steel in the casting process

Effect of Mn Addition to Al–Si Alloy on the Layer Formed at the Interface with Cast Iron in Compound Casting

Effect of Aluminum, Copper and Manganese on the Structure and Properties of Cast Irons

Control of High-Temperature Static and Transient Thermomechanical Behavior of SiMo Ductile Iron by Al Alloying

Effect of Si content on interfacial reaction and properties between solid steel and liquid aluminum

Effect of Chemical Compositions on Tensile Behaviors of High Pressure Die-Casting Alloys Al-10si-Ycu-Xmn-Zfe

Effect of CaO/SiO2 and Al2O3/SiO2 Mass Ratios on Structure and Viscosity of Mold Flux for Continuous Casting High‐Mn High‐Al Steel

Unveiling the effect of MnO/SiO2 ratios on the viscosity and structure of mold fluxes for high-Mn cryogenic steels

Research Status of High-Manganese High-Aluminum Steel and Key Points of Continuous Casting

Secondary Al-Si-Mg High-pressure Die Casting Alloys with Enhanced Ductility

Wear Behavior and Microstructure Changes of a High Chromium Cast Iron: The Combined Effect of Heat Treatment and Alloying Elements

Iron Intermetallic Phases in the Alloy Based on Al-Si-Mg by Applying Manganese

Bonding Strength and Grain Size Control of Dissimilar Joints of Al-Mg Alloys with Forge Welding

New Technologies of Aluminum Castings. Effect of Microstructure on Fracture Toughness of Cast and Forged Aluminum Casting Alloys.

High-temperature oxidation behavior and subsurface phase transformation of high-Mn high-Al steel