Abstract:Highlights • Microstructure and mechanical behavior of Al-xSi/AZ91D bimetallic composites were studied. • Thickness of interface of Al/Mg bimetallic composites decreased with increasing Si content. • Oxide inclusion defects in interface layer decreased with increasing Si content. • Increasing Si content resulted in an inconsistent preferred orientation of interface layer. • Shear strength of the composites increased with increasing Si content, obtaining a maximum value with 15 wt.% Si. In this paper, the effect of the Si content on microstructure evolution, mechanical properties, and fracture behavior of the Al-xSi/AZ91D bimetallic composites prepared by compound casting was investigated systematically. The obtained results showed that all the Al-xSi/AZ91D bimetallic composites had a metallurgical reaction layer (MRL), whose thickness increased with increasing Si content for the hypoeutectic Al-Si/AZ91D composites, while the hypereutectic Al-Si/AZ91D composites were opposite. The MRL included eutectic layer (E layer), intermetallic compound layer (IMC layer) and transition region layer (T layer). In the IMC layer, the hypereutectic Al-Si/AZ91D composites contained some Si solid solution and flocculent Mg 2 Si+Al-Mg IMCs phases not presented in the hypoeutectic Al-Si/AZ91D composites. Besides, increasing Si content, the thickness proportion of the T layer increased, forming an inconsistent preferred orientation of the MRL. The shear strengths of the Al-xSi/AZ91D bimetallic composites enhanced with increasing Si content, and the Al-15Si/AZ91D composite obtained a maximum shear strength of 58.6 MPa, which was 73.4% higher than the Al-6Si/AZ91D composite. The fractures of the Al-xSi/AZ91D bimetallic composites transformed from the T layer into the E layer with the increase of the Si content. The improvement of the shear strength of the Al-xSi/AZ91D bimetallic composites was attributed to the synergistic action of the Mg 2 Si particle reinforcement, the reduction of oxidizing inclusions and the ratio of Al-Mg IMCs as well as the orientation change of the MRL.

Effect of Si content on interfacial reaction and properties between solid steel and liquid aluminum

Influence of Si content on interfacial reactions and mechanical properties of dual-spot laser welded-brazed Ti/Al joints

Effect of Si on Fe-rich intermetallic formation and mechanical properties of heattreated Al-Cu-Mn-Fe alloys

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effects of Si contents in filling wires on microstructure evolution and properties of Al-steel dissimilar joint by laser welding-brazing

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Evolution of Iron-Rich Intermetallics and its Effect on the Mechanical Properties of Al-Cu-Mn-Fe-Si Alloys after Thermal Exposure and High-Temperature Tensile Testing

Influence of silicon addition on intercritical annealing process and tensile properties of medium Mn steel

The Growth Behavior for Intermetallic Compounds at the Interface of Aluminum-Steel Weld Joint

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Effect of Si on Phase Equilibria, Mechanical Properties and Tribological Behaviour of Al-Cu Alloy

Effect of Fe and Mn Content on the Microstructures and Tensile Behaviour of AlSi7Cu3 Alloy: Thermal Analysis and Tensile Tests

Kinetics of intermetallic compound layers between AISI 321 stainless steel and molten aluminum

Effects of metalloid Si on the microstructure and mechanical properties of Fe36Ni36Cr10Mo1Al17-XSiX alloys

Effect of Iron-Rich Intermetallic and Eutectic Si Accumulation on Al-Si-Mg Alloy

Effects of Si solution in θ-Al13Fe4 on phase transformation between Fe-containing intermetallic compounds in Al alloys

The effect of Si addition on the microstructure and tensile properties of casting Al-5.0Cu-0.6Mn-1.2Fe alloys

Influence of Si contents on the microstructure and corrosion resistance of the Zn−Al−Mg−Si alloys

Effect of Fe and Si on the Phase Composition and Microstructure Evolution in Al-2 wt.% Cu-2 wt.% Mn Alloy During Solidification, Cold Rolling and Annealing

Effect on Wetting Properties of the Al-Ti System by the Addition of Different Alloying Elements

Microstructure evolution, mechanical properties and fracture behavior of Al-xSi/AZ91D bimetallic composites prepared by a compound casting