Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400–500 °C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large-scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 °C. At the optimal sintering temperature (130 °C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8–1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.5Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m–1 K–1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03540.Single parabolic band model and calculated transport properties; EBSD analysis for pellet sintered at 110 °C; BSE, EDS mapping, and TEM images of pellet sintered at 130 °C; average ZT values; and XPS results (PDF)This article has not yet been cited by other publications.

Low‐Temperature Thermophotovoltaic Cells by Bonding Bi2Te3 and Si Wafers

Bi2Te3/Si thermophotovoltaic cells converting low temperature radiation into electricity

Bi2Te3/Sb2Te3 Heterojunction and Thermophotovoltaic Cells Absorbing the Radiation from Room-temperature Surroundings

Three-junction Tandem Photovoltaic Cell for a Wide Temperature Range Based on a Multilayer Circular Truncated Cone Metamaterial Emitter

Expand band gap and suppress bipolar excitation to optimize thermoelectric performance of Bi0.35Sb1.65Te3 sintered materials

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Optimized Thermoelectric Properties of Bi0.48Sb1.52Te3 Through AgCuTe Doping for Low-Grade Heat Harvesting.

Sb2Te3 based alloy with high thermoelectric and mechanical performance for low-temperature energy harvesting

High Thermoelectric Performance Bismuth Telluride Prepared by Cold Pressing and Annealing Facilitating Large Scale Application

Surfactant-free Synthesis of Bi2Te3-Te Micro-Nano Heterostructure with Enhanced Thermoelectric Figure of Merit.

High-Temperature Thermoelectric Monolayer Bi2TeSe2 with High Power Factor and Ultralow Thermal Conductivity

Integrating band engineering with point defect scattering for high thermoelectric performance in Bi2Si2Te6

Room‐Temperature High‐Performance Thermoelectric Bi0.6Sb0.4Te: Elimination of Detrimental Band Inversion in BiTe

In Situ Synthesis of High Thermoelectric Performance Bi2Te3 Flexible Thin Films through Thermal Diffusion Engineering

High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

Synergistic Texturing and Bi/Sb‐Te Antisite Doping Secure High Thermoelectric Performance in Bi 0.5 Sb 1.5 Te 3 ‐Based Thin Films

High Photon-to-heat Conversion Efficiency in the Wavelength Region of 250–1200 Nm Based on a Thermoelectric Bi2Te3 Film Structure

High-Temperature Thermoelectric Monolayer Bi 2 TeSe 2 with High Power Factor and Ultralow Thermal Conductivity

Broadening the optimum thermoelectric power generation range of p-type sintered Bi0.4Sb1.6Te3 by suppressing bipolar effect

BiSbTe alloy with high thermoelectric and mechanical performance for power generation

Thermoelectric performance of p-type (Bi,Sb)2Te3 incorporating amorphous Sb2S3 nanospheres