Abstract:Titanium alloys are widely employed in aerospace applications due to an outstanding combination of properties. The variety of loading conditions and microstructures encountered in industrial components is urging the development of microstructure sensitive modeling capabilities. In particular, reliable predictions require a good knowledge of operating deformation mechanisms. The present study aims at providing a thorough characterization of deformation mechanisms in the near-α Ti-6Al-2Sn-4Zr-2Mo alloy using experiments and simulations. The sequential activation of deformation mechanisms in the α phase was monitored in situ during a tensile test carried out in a scanning electron microscope using a combination of slip traces analysis and electron back-scattered diffraction. Basal slip is activated first, and prismatic slip activity, which proceeds at a higher macroscopic stress level, is needed for a significant creep/relaxation to occur. While little evidence of -type pyramidal slip was found, pyramidal slip involved first-order pyramidal planes and operates at stress levels near or above the 0.2% proof stress. Atomic force microscopy characterization of the features of the different slip modes revealed that slip is coarser and wavier than slip. Twinning, which is usually neglected in such alloys within this strain regime, was observed to be slip stimulated at a plastic strain as low as 0.5 %. Crystal plasticity parameters leading to an accurate simulation of the activation sequence of deformation mechanisms were then determined. For this purpose, critical resolved shear stress values were derived for the different slip and twinning modes using specific approaches and subsequently validated using crystal plasticity simulations based on fast-Fourier transforms.

Dynamic necking of a near α titanium alloy at high strain rates: Experiments and modelling

Modeling the Strain Rate-Dependent Constitutive Behavior in Nanotwinned Polycrystalline Metals

Strain Rate Sensitivity of Tensile Properties in Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy: Experiments and Constitutive Modeling

Dynamic Strain-Rate Effect On Uniaxial Tension Deformation Of Ti5al2.5sn Alpha-Titanium Alloy At Various Temperatures

Thermomechanical Response of Commercially Pure Titanium under Large Plastic Deformation at High Strain Rates

Strain-Rate-Dependent Tensile Response of Ti–5Al–2.5Sn Alloy

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

Neutron Diffraction Study on Strain Rate Dependent Mechanical Response in Superelastic NiTi Alloy: Bulk Structural Evolution and Constitutive Model

Dynamic Mechanical Properties and Modified Material Constitutive Model for Hot Forged Ti2AlNb over Wide Ranges of Temperature and Strain Rate

Hot Deformation and Constitutive Modeling of TC21 Titanium Alloy

Dynamic Deformation Behavior and Fracture Characteristics of a near α TA31 Titanium Alloy at High Strain Rates

Temperature-Dependent Tension Plastic Deformation and Fracture Behavior of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates

The Constitutive Responses of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates and Elevated Temperatures

Deformation mechanisms in the α phase of the Ti-6Al-2Sn-4Zr-2Mo titanium alloy: in situ experiments and simulations

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading

Tension behavior of Ti–6.6Al–3.3Mo–1.8Zr–0.29Si alloy over a wide range of strain rates

Microstructure evolvement of isometry TiAl under tensile impact loadings

Experimental Study on Tension Behavior of Pure Titanium at High Strain Rates

Effect of Microstructure on High-Speed Tensile Mechanical Properties of Ti-1300 Alloy

Strain Rate Sensitivity and Adiabatic Shear Deformation of an Advanced Al-Mg Alloy

High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling