Abstract:This research work focuses on exploring various new nanomaterials for saturable absorber (SA) application in generating Q-switched and Mode-locked pulses operating at 1 μm region. These nanomaterials are Molybdenum disulfide (MoS2), Black Phosphorus (BP), Topological Insulator (TI): Bismuth (III) Selenide (Bi2Se3), Bismuth (III) Telluride (Bi2Te3), and antimony telluride (Sb2Te3), and metal oxide: Nickle Oxide (NiO) nanoparticles and cobalt oxide (Co3O4) nanocubes. The fiber laser employs Ytterbiumdoped fiber (YDF) as a gain medium. Firstly, molybdenum disulfide (MoS2) was proposed. The Q-switched laser was obtained by using few layers MoS2, which was mechanically exfoliated by using a scotch tape. The SA was sandwiched between two fiber ferrules to form a fiber compatible Q-switcher. By incorporating the SA inside the YDFL cavity, a stable pulse laser operating at 1070.2 nm wavelength was generated with the repetition rate was tunable from 3.817 to 25.25 kHz. A passively mode-locked YDFL was demonstrated using a few layered MoS2 film which was obtained by a liquid phase exfoliation technique. The mode-locking pulses have a repetition rate of 18.8 MHz and pulse energy of 0.1 nJ. Secondly, mechanically exfoliated Black phosphorus (BP) was proposed for both Q-switching and mode-locking pulses generation. The Q-switched laser has a pump threshold of 55.1 mW, a pulse repetition rate that is tunable from 8.2 to 32.9 kHz, the narrowest pulse width of 10.8 μs and the highest pulse energy of 328 nJ. BP based mode-locked YDFL was obtained by improving the SA preparation. The laser operated at 1033.76 nm with a fixed repetition rate of 10 MHz. Passively Q-switched YDFLs was also successfully demonstrated using a few-layers Bi2Se3, Bi2Te3 and antimony telluride (Sb2Te3) based SAs. For instance, a Sb2Te3 film based Q-switched YDFL produced pulse repetition rate, which was tunable from 24.4 to 55 kHz with the maximum pulse energy of 252.6 nJ at 82.3 mW pump power. The mode-locked YDFL operating at 24.2 MHz repetition and 18.8 ps pulse width were also realized with Sb2Te3 based SA. Finally, two transition metal oxide nanomaterials: Nickel Oxide (NiO) and cobalt oxide (Co3O4) were embedded into a polymer film, making it an SA device for both Q-switched and mode-locked YDFLs. Stable Q-switched and mode-locked YDFLs were realized with both materials. For instance, the mode-locked Co3O4 based YDFL was operated at 1035.8 nm wavelength with a fixed repetition rate of 20 MHz and picoseconds pulse width. In short, an efficient and low-cost Q-switched and mode-locked YDFLs operating in 1 μm region have been successfully achieved by utilizing various new nanomaterials as SA.

Mode-Locking and Q-Switching in Holmium Doped Fiber Laser Using Topological Insulator (Sb2Te3) as Saturable Absorber

3-Μm Mid-infrared Pulse Generation Using Topological Insulator As the Saturable Absorber.

Mode-Locked YDFL Using Topological Insulator Bismuth Selenide Nanosheets as the Saturable Absorber

106Μm Q-switched Ytterbium-Doped Fiber Laser Using Few-Layer Topological Insulator Bi_2Se_3 As a Saturable Absorber

A practical topological insulator saturable absorber for mode-locked fiber laser

Mid-infrared ultra-short mode-locked fiber laser utilizing topological insulator Bi2Te3 nano-sheets as the saturable absorber

Mode-locked Thulium-Holmium doped Fiber Laser using Bi2Se3 Saturable Absorber Deposited onto Arc-shaped and Side-polished fibers via Airbrush Spraying Technique

Femtosecond harmonic mode-locking of a fiber laser based on a bulk-structured Bi(2)Te(3) topological insulator

Ultralow Saturation Intensity Topological Insulator Saturable Absorber for Gigahertz Mode-Locked Solid-State Lasers

1.06 μm Q-switched ytterbium-doped fiber laser using few-layer topological insulator Bi2Se3 as a saturable absorber

Realization of Harmonic Mode-Locking in Thulium-Doped Fiber Laser Using In2(SO4)3-based Saturable Absorber

A femtosecond pulse erbium fiber laser incorporating a saturable absorber based on bulk-structured Bi2Te3 topological insulator

70-fs mode-locked erbium-doped fiber laser with topological insulator

70 fs hybrid mode-locked Erbium-doped fiber laser with topological insulator

Q-switching and mode-locking pulse generation in Ytterbium-doped fiber lasers using nanomaterial saturable absorbers / Ahmed Hasan Hamood al-Masoodi

A femtosecond pulse fiber laser at 1935 nm using a bulk-structured Bi2Te3 topological insulator

Topological Insulator-Assisted Dual-Wavelength Fiber Laser Delivering Versatile Pulse Patterns

Ti3C2 MXene as an optical modulator in a Thulium/Holmium-doped fiber laser

Passively Q-switched 1.56 μm all-fiberized laser based on evanescent field interaction with bulk-structured bismuth telluride topological insulator

Titanium Disulfide Based Saturable Absorber for Generating Passively Mode-Locked and Q-Switched Ultra-Fast Fiber Lasers

Passively Q-switched and mode-locking fiber laser based on Sb2S3 saturable absorber