Abstract:The present study reports the influence of graphene layers on the tribological performance of CVD diamond films when they are used as the solid lubricants. Friction tests are conducted on a ball-on-plate friction tester, where the stainless steel is used as the counterpart material. The CVD diamond film sample is a typical microcrystalline diamond (MCD) coating which is deposited on a flat tungsten carbide substrate using the hot filament chemical vapor deposition method (HFCVD). Besides the MCD sample, a polished MCD film (pMCD) and a polished tungsten carbide (pWC) are also adopted in frictional tests, aiming at illustrating the influence of the surface morphology, as well as the physical property, of the sample on the lubricative effect of graphene layers. The experimental results show that graphene layers can effectively reduce the coefficient of friction (COF), regardless of the samples. The MCD sample presents the lowest stable COF, which is 0.13, in dry sliding period when the graphene flakes are sparyed on the sliding interface; while the pMCD and pWC samples exhibit slightly higher COFs, which are 0.16 and 0.18, respectively. Comparatively, the COFs of these three samples obtained in dry sliding process without graphene are 0.20, 0.25 and 0.64. In additon, the MCD sample exhibits a much longer stable dry slidng process which is more than 5000 cycles. Comparatively, the other two tribo-pairs only exhibit a stable low-COF dry sliding period for around 2000 cycles. The reduction of COF could be attributed to the graphene flakes adhered on the sliding interface. It forms a layer of solid lubricative film with extremely low shear strength and significantly decreases the interactions between two contacted surfaces. The rugged surface of the MCD film provides sufficient clogging locations for graphene flakes, which allows the generated lubricative film enduring a long sliding duration. It can be arrived from this study that the tribological properties of the MCD film could be enhanced by simply adoping graphene layers as a solid lubricant. Furthermore, an improved performance of a variety of MCD coated cutting tools or mechanical components could be expected when they are utilized with graphene layers.

Effect of the additive multilayer graphene on the enhanced tribological properties of ultra-coarse WC-Co cemented carbides

Microstructure, mechanical and tribological properties of multilayer grapheme reinforced WC-10Ni 3 Al prepared by microwave sintering

Wear behaviour of graphene platelets reinforced WC-Co cemented carbide

Effect of Graphene on the Microstructure and Mechanical Properties of WC-Based Cemented Carbide

Tribological performance of binderless tungsten carbide reinforced by multilayer graphene and SiC whisker

Preparation and Tribological Properties of Graphene-Based Coatings on Tungsten Carbide

High-hard and High-Tough WC-TiC-Co Cemented Carbide Reinforced with Graphene

On the Enhanced Wear Resistance of Ultra-Coarse WC-Co Cemented Carbides by WCoB Addition

Enhanced Tribological Performance of CVD Diamond Films Enabled by Using Graphene Layers As Solid Lubricant

Effect of Multilayer Graphene and Fe2O3 Nanoparticles on Wear Behavior of TC11 Alloy

Improving wear performance of CuSn5Bi5 alloys through forming self-organized graphene/Bi nanocomposite tribolayer

Coordinating influence of multilayer graphene and spherical SnAgCu for improving tribological properties of a 20CrMnTi material

Enhancement on the tribological performance of diamond films by utilizing graphene coating as a solid lubricant

Synergistic effects of TiC and graphene on the microstructure and tribological properties of Al2024 matrix composites

Effect of MWCNTs on microstructure and properties of WC-9Co gradient cemented carbides

Performance Enhancement of Ultra-Coarse Cemented Carbide by Boride Additives

Modification of microstructure and properties of Ti-47Al-2Cr-4Nb-0.3W alloys fabricated by SPS with trace multilayer graphene addition

Tribological properties and wear resistance mechanism of WC-ZrO2-Al2O3 ceramics

Design and characterization of metallic glass/graphene multilayer with excellent nanowear properties

Cutting performance and wear mechanism of multilayer diamond coated tools

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides