Abstract:In this paper, Cu thin films were deposited on Si (100) substrates by the high-power impulse magnetron sputtering (HiIPMS) technique, and the effects of different duty cycles (from 2.25% to 5.25%) on the plasma discharge characteristics, microstructure, and electrical properties of Cu thin films were investigated. The results of the target current test show that the peak target current remains stable under 2.25% and 3% duty cycle conditions. Under the conditions of a 4.5% and 5.25% duty cycle, the target peak current shows a decreasing trend. The average power of the target shows a rising trend with the increase in the duty cycle, while the peak power of the target shows a decreasing trend with the increase in the duty cycle. The results of OES show that with the increase in the duty cycle, the total peak intensity of copper and argon emissions shows an overall increasing trend. The duty cycle from 3% to 4.5% change in copper and argon emission peak total intensity change is not obvious. The deposition rate and surface morphology of the copper film were investigated by scanning electron microscopy, and the deposition rate of the copper film increased with the increase in the duty cycle, which was mainly due to the increase in the average power. The surface roughness of the copper film was evaluated by atomic force microscopy. X-ray diffraction (XRD) was used to analyze the grain size and texture of the Cu film, and the results showed that the average grain size of the Cu film increased from 38 nm to 59 nm on the (111) and (200) crystal planes. Four-probe square resistance test copper film resistivity in 2.25%, 3% low duty cycle conditions of the copper film resistivity is generally higher than 4.5%, 5.25% high duty cycle conditions, the copper film resistivity shows the trend of change is mainly affected by the copper film grain size and the (111) face of the double effect of the optimal orientation. The lowest resistivity of the copper film measured under the 4.5% duty cycle condition is 1.7005 μΩ·cm, which is close to the intrinsic resistivity of the copper film of 1.67 μΩ·cm.

Effect of oxygen flow rate ratio on crystalline phase and properties of copper oxide films prepared by room-temperature high-power impulse magnetron sputtering

Low Resistivity Transparent Conducting CdO Thin Films Deposited by DC Reactive Magnetron Sputtering at Room Temperature

Influence of Oxygen Flow Rate on the Phase Structures and Properties for Copper Oxide Thin Films Deposited by RF Magnetron Sputtering

Influence of O_2/Ar Flow Ratio on Microstructures and Photoluminescence of ZnO Films

Modulation of the conductive behavior of NiO thin film deposited by HiPIMS through varying the O2 flow ratio

Modulation of optical and electrical properties of In2O3 films deposited by high power impulse magnetron sputtering by controlling the flow rate of oxygen

Oxide phase and conductivity-type of copper oxide thin films deposited by direct current magnetron sputtering

Fabrication of P-Type Copper Oxide Thin-Film Transisters at Different Oxygen Partial Pressure

Electrical and optical properties of copper oxide thin films prepared by DC magnetron sputtering

The effects of oxygen flow ratio on the properties of Ag x O thin films grown by radio frequency magnetron sputtering

Effects of HiPIMS Duty Cycle on Plasma Discharge and the Properties of Cu Film

Influence of Target Current on Structure and Performance of Cu Films Deposited by Oscillating Pulse Magnetron Sputtering

In-Sn-Zn Oxide Nanocomposite Films with Enhanced Electrical Properties Deposited by High-Power Impulse Magnetron Sputtering

Influence of oxygen flux on properties of nickel oxide films prepared by magnetron sputtering for alternative hole-transporting layer in inverted perovskite solar cells

Influence of HiPIMS Pulse Widths on the Structure and Properties of Copper Films

Effect of oxygen flow ratio on crystallization and structural characteristics of gallium oxide thin films

The structural, electrical, and optical properties of SnO2 films prepared by reactive magnetron sputtering: Influence of substrate temperature and O2 flow rate

Effect of Oxygen Flow on the Optical Properties of Hafnium Oxide Thin Films by Dual-Ion Beam Sputtering Deposition

Effect of Oxygen Flow Rate on the Optical, Electrical, and Mechanical Properties of DC Sputtering ITO Thin Films

Effects of Oxygen Flows and Annealing Temperatures on Optical, Electrical, and Structural Properties of Co-Sputtered In2O3-Ga2O3-Zn Thin Films

The effect of substrate temperature and oxygen partial pressure on the properties of nanocrystalline copper oxide thin films grown by pulsed laser deposition