Abstract:Purpose. To show the effectiveness of various methods of heat treatment of the studied steels with heating in ITI, as a result of which their mechanical properties are increased, which is due to the acquisition of a multiphase structure, one of the components of which in some cases is metastable austenite. Research methods. Steels 14Г2, 20ГЛ, 20ГФЛ 45Г were investigated. Various types of heat treatment were carried out with heating in the intercritical temperature interval. In the studied steels, a multiphase structure dispersed in chemical composition was obtained. Durometric, metallographic and X-ray research methods were used. Mechanical properties under tension and impact toughness were determined. These properties were compared with those obtained from the studied steels after typical heat treatment. Obtained results. It is shown that in the investigated steels, when performing various methods of heat treatment, there is no need to obtain a single-phase austenite structure, which is homogeneous in terms of its chemical composition, during heating. The creation of a multiphase dispersed micro-inhomogeneous structure in the studied steels by heat treatment methods, which include regulated heating and holding in ITI, allows to obtain after normalization, hardening and high or low tempering, as well as isothermal tempering, a good combination of strength and plastic properties, the level of which exceeds that obtained after the usual process. Scientific novelty. The paper considers an alternative point of view, according to which to improve the mechanical and service properties of steels, it is necessary to obtain multiphase dispersed micro-inhomogeneous structures in them, consisting of martensite, bainite, ferrite, carbides, carbonitrides and metastable residual austenite, as well as their various combinations. In order to obtain such structures, it is advisable to use heating and holding in ITI during the heat treatment of pre-eutectoid steels, in which austenite is formed, along with ferrite and carbides. At the same time, austenite has chemical micro-heterogeneity, because the carbon concentration at its boundary with carbide is significantly higher than at the boundary with ferrite. This makes it possible to obtain a multiphase dispersed micro-inhomogeneous structure after heat treatment. Practical value. Increasing the mechanical properties of steels makes it possible to increase the operational stability of machine parts, which is an important task of materials science. One of the directions of its solution is to obtain a multiphase structure in steels, one of the components of which is metastable austenite, in which the dynamic deformation martensitic transformation (DSMT) and the effect of self-hardening under load (SHL) occur under load. Methods of heat treatment with heating at ITI are easily implemented in production conditions and allow for energy savings. Modes of their implementation should be chosen taking into account obtaining the necessary properties, the initial structure, its defects and the cross-section of the products.

Heat treatment effect on the carbides in T-15 and M-4 steels

Features of the Heat Treatment of High Speed Steel

Heat Treatment Effect on the Microstructural, Hardness and Tribological Behavior of A105 Medium Carbon Steel

Influence of thermo-mechanical and solution annealing treatments on the flow behaviour of 14Cr-15Ni stainless steel

Enhancing the life of forging dies by investigating different heat treatment methods

Microstructural variations and mechanical properties of deep cryogenic treated AISI M35 high-speed steel tempered at various temperatures

Effect of deep cryogenic treatment on the mechanical properties of tool steels

Effect of Deep Cryogenic Time on Martensite Multi-Level Microstructures and Mechanical Properties in AISI M35 High-Speed Steel

The Microstructure and Mechanical Properties of Ferritic-Martensitic Steel EP-823 after High-Temperature Thermomechanical Treatment

Effect of Heat Treatment on the Microstructural Heterogeneity and Abrasive Wear Behavior of ASTM A128 Grade C Steel

Heat Treatment of High Manganese Austenitic Steel: Structural and Mechanical Properties

The effect of deep cryogenic treatments on the mechanical properties of an AISI H13 steel

On the Use of Cyclic Cryogenic Treatment to Improve the Properties of High-Speed Steel

Microstructure evolution and mechanical properties of T15 high speed steel prepared by twin-atomiser spray forming and thermo-mechanical processing

STRUCTURE AND MECHANICAL PROPERTIES OF A SERIES OF STRUCTURAL STEEL AFTER HEAT TREATMENT WITH ENDURANCE IN THE INTERCRITICAL TEMPERATURE INTERVAL

Effect of Heat Treatment on Phase Transformation Texture and Mechanical Properties in Hot-Rolled High-Strength Steels

Effect of Heat Treatment Temperature on the Microstructure, Wear and Friction of Ni–Nb–V Alloyed Manganese Steel

Effect of high-temperature thermomechanical treatment on microstructure and mechanical properties of an austenitic steel with dispersed particles

Effect of Heat Treatment Parameters on Mechanical Properties of Medium Carbon Steel

Effect of Heat Treatment on Structure and Properties of B Alloyed High Speed Steel for Rolling Mill Rolls

Effect of different heat treatments on microstructure and mechanical properties of 60CrNiMo steel