Abstract:The present work is focused on the multidirectional forging (MDF) of Al–20 wt-% Si alloys with the addition of refiners and modifiers. The MDF process was performed at 200°C with a cumulative strain of 0.63. Microstructural characterization and mechanical performance were evaluated on the Al–20Si, Al–20Si–4.5Cu, Al–20Si–4.5Cu–1(Al–Ti–B), Al–20Si–4.5Cu–1(Al–Ti–B)–10(Al–Sr). The microstructure analysis revealed significant changes in the eutectic and primary phase refinement. The micro-Vickers hardness confirmed that the MDF process resulted in increased hardness (125 ± 1.9 VHN) compared to the homogenized samples (96 ± 2.7 VHN). Tensile test results showed that with the accumulation of strain, ultimate tensile strength increased to 435 MPa from 302 MPa with reduction in the percentage of elongation from 7.8 to 5.6. The grains were more uniformly distributed with addition of modifiers, and refiners further reduced the nucleation number of eutectic grains. The wear study demonstrated that the wear resistance is more in the Al–Si-Cu-Sr sample due to the increased level of hardness. The combination of multidirectional forging techniques with judicious incorporation of refiners and modifiers engenders a synergistic enhancement of microstructural integrity, hardness profiles, and wear-resistant properties in hypereutectic Al-20Si alloys. Le travail courant se concentre sur le forgeage multidirectionnel (MDF) des alliages Al-20% en poids Si avec ajout d'agents d'affinage et modificateurs. On a réalisé le procédé MDF à 200°C sur trois passes avec une déformation cumulée de 0.63. Suite au procédé MDF, on a évalué la caractérisation microstructurale et les performances mécaniques sur Al–20Si, Al–20Si–4.5Cu, Al–20Si–4.5Cu–1(Al–Ti–B) et Al–20Si–4.5Cu–1(Al–Ti–B)–10(Al–Sr). L'analyse de la microstructure a révélé des changements significatifs dans le raffinement de la phase eutectique et primaire après le traitement MDF. Les essais de microdureté Vickers ont confirmé que le procédé MDF entraînait une dureté accrue (125 ± 1.9 VHN) par rapport aux échantillons homogénéisés (96 ± 2.7 VHN). Les résultats des essais de traction ont montré qu'avec l'accumulation de déformation, la résistance ultime à la traction a augmenté de 302 MPa à 435 MPa avec une réduction du pourcentage d'allongement de 7.8 à 5.6. Les grains étaient distribués plus uniformément avec l'ajout d'agents modificateurs, et les agents d'affinage ont réduit davantage le nombre de nucléation des grains eutectiques. L'étude d'usure a démontré que la résistance à l'usure est supérieure dans l'échantillon Al–Si–Cu–Sr en raison du niveau de dureté accru. La combinaison des techniques de forgeage multidirectionnel avec l'incorporation judicieuse d'agents d'affinage et modificateurs engendre une amélioration synergique de l'intégrité microstructurale, des profils de dureté et des propriétés de résistance à l'usure des alliages hypereutectiques Al–20Si.

Enhancing the life of forging dies by investigating different heat treatment methods

Effects of deep cryogenic treatment on the microstructure evolution, mechanical and thermal fatigue properties of H13 hot work die steel

The effect of deep cryogenic treatments on the mechanical properties of an AISI H13 steel

The Effect of Cryogenic Treatment on a High Co Bearing DIN 1.2888 Steel Used as Die in Hot Forging Process

Effect of multidirectional forging on grain structure and mechanical properties of hypereutectic Al–20%Si alloys with added refiners and modifiers

Heat treatment effect on the carbides in T-15 and M-4 steels

Effects of traditional heat treatment and a novel deep cryogenic treatment on microstructure and mechanical properties of low-carbon high-alloy martensitic bearing steel

Effect of deep cryogenic treatment on the mechanical properties of tool steels

Experimental Investigation on the Effect of Deep Cryogenic Treatment on 100 Cr6 Bearing Steel

Effects of deep cryogenic treatment on machinability, hardness and microstructure in dry turning process of tempered steels

Enhancing the Wear Resistance of 100Cr6 Bearing Steel Using Cryogenic Treatment

Effect of multiple deep cryo-treating and tempering on microstructure and property evolution of high carbon bearing steel

Impact of a Multi-step Heat Treatment on Different Manufacturing Routes of 18CrNiMo7-6 Steel

Influence of Deep Cryogenic Treatment on the Mechanical Properties of AISI 440C Bearing Steel

Influence of Deep Cryogenic Treatment and Secondary Tempering on Microstructure and Mechanical Properties of Medium-Carbon Low-Alloy Steels

Experimental Investigation on the Effect of Deep Cryogenic Treatment on 100Cr6 Bearing Steel

Optimization of Deep Cryogenic Treatment Process for 100Cr6 Bearing Steel Using the Grey-Taguchi Method

Deep Cryogenic Treatment Improves Wear Resistance of En 31 Steel

Influence of thermo-mechanical and solution annealing treatments on the flow behaviour of 14Cr-15Ni stainless steel