Abstract:The superplastic blow forming limits for a 5083 aluminum alloy were investigated at a strain state from the plane strain to the balanced biaxial at a temperature of 773 K and a strain rate of about 1 � 10� 3 s� 1. It was discovered that the equivalent strain at the forming limit was in a range of 1:3 � 0:1 for every strain state and was consistent with that obtained by the uniaxial tensile tests. Namely, the forming limit for the blow forming could be estimated from the equivalent strain-to-fracture in the uniaxial tensile test. The cavity volume fraction and the cavity growth rate at the forming limit, however, increased by changing the strain state from uniaxial to balanced biaxial through a plane strain. The relationship between the forming limit and the cavity volume fraction is dependent upon the strain state. Most research on the deformation characteristics of super- plastic materials has been carried out using uniaxial tensile tests to evaluate the flow stress, strain rate sensitivity, elongation and cavity volume fraction at various temper- atures and strain rates. The uniaxial tensile tests at high temperatures facilitated a comparison of the phenomena of creep and superplasticity and enabled the elucidation of the scientific characteristics of superplasticity. However, it is difficult to accurately estimate the capability of the super- plastic blow forming from the results of the uniaxial tensile test. The superplastic blow forming is usually performed under the biaxial tensile conditions. Therefore, the deforma- tion characteristics of the materials under the biaxial tension at high temperatures are required in order to compare them with those under the uniaxial tension. For instance, the prediction of the forming limit for the biaxial tension from the uniaxial tension is expected. There are many studies on the experimental and theoretical research regarding the cold press-forming limit for steels and aluminum alloys. 1-7) The theoretical and experimental results for the cold press- forming limit diagram showed that the minor strain at the plane strain state was lower than that at the biaxial strain state because the effect of the strain rate sensitivity on the plastic stability was not expected at room temperature. There are a few reports on the superplastic-forming limit. 8) Mahoney et al. carried out the superplastic deformation for the 7475 aluminum alloy at the uniaxial tension, the plane strain and the balanced biaxial strain state. 8) They showed that a forming limit diagram was developed to relate the damage due to cavitation during forming to a corresponding decrease in the mechanical properties and that a major strain at the plane strain was as large as that at the biaxial strain state. They also described that the strain state has no measurable influence on cavity growth rate during the superplastic forming. The result is somewhat surprising since the mean stress is known to influence cavitation in creep and super- plasticity. 9) In this study, a superplastic blow-forming machine was constructed for laboratory use in which the pressure-time path was precisely controlled by a personal computer. Using this equipment, the superplastic forming for a 5083 aluminum alloy was performed in a range of strain state from a plane strain to a balanced biaxial strain. The purpose of this study is to show the forming-limit diagram for a 5083 alloy and a relationship between the forming limit and cavitation.

Superplastic forming under hydrostatic pressure and heat treatments in an Al-Li alloy.

Forming Limit Diagram for a Superplastic 5083 Aluminum Alloy

Effects of hydrostatic pressure and non-uniform microstructure on superplastic forming and postformed tensile properties of AA 7475 aluminium alloy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Experimental and Numerical Investigation on Strengthening Behavior of 7075 Aluminum Alloy Sheets in Hot Forming–Quenching Integrated Process

Strength and Formability Improvement of Al-Cu-Mn Aluminum Alloy Complex Parts by Thermomechanical Treatment with Sheet Hydroforming

Superplastic Deformation Behavior of As-Received and Hydrogenated Ti2AlNb Alloy

Study on the Aging Precipitation Behavior and Kinetics of Al-10.0Zn-3.0Mg-2.8Cu Alloy by Pre-Deformation Treatment

Application of Combined W-Temper and Cold Forming Technology to High-Strength Aluminum Alloy Automotive Parts

Investigation of Pre-Aged Hardening Single-Point Incremental Forming Process and Mechanical Properties of AA6061 Aluminum Alloy

Investigation of formability, microstructures and post-forming mechanical properties of heat-treatable aluminum alloys subjected to pre-aged hardening warm forming

Evaluation of the formability of AA2198-T3 Al-Li alloy in warm sheet hydroforming

Crystal Plasticity Finite Element Analyses on the Formability of AA6061 Aluminum Alloy with Different Ageing Treatments

Strength-plasticity transition mechanism after the solution treatment of GH3230 superalloy fabricated via laser powder bed fusion

Development of a strain dependent pressure law for superplastic forming of 2024 aluminium alloy

Mechanisms and microstructures of 2A97 Al-Li alloy under the hot forming with synchronous quenching process

Effect of Heat Treatment Conditions on Mechanical Properties and Precipitates in Sheet Metal Hot Stamping of 7075 Aluminum Alloy

Hot Stamping of a B-Pillar Reinforced Panel With 7075 Aluminum Alloy and the Feasibility Study of Short-Time Aging

Study on High-Temperature Mechanical Properties and Forming Limit Diagram of 7075 Aluminum Alloy Sheet in Hot Stamping

Investigation on the ageing behaviour and hardening mechanisms of 5A90 Al–Li alloy U-shaped parts formed by electric resistance heating forming-quenching process

Effect of Thermo-Mechanically Activated Precipitation on the Hot Deformation Behavior of High Strength Aluminum Alloy AA7075