Abstract:The effect of a spray rubber adhesive frequently used in liquid composite molding (LCM) processes on the longitudinal velocities during the impregnation of resin on thin (2–3 mm) carbon fiber preforms is reported. Experimental observations show that application of this adhesive invariably results in a lower mold filling time when compared to the corresponding observations in the same laminated configurations without adhesive. That is notwithstanding the greater delay in the resin flow front at the rigid mold surface. These effects were systematically observed in single and multi-fiber stacks. Fill-up time differences up to 30 % and flow front delayed distances up to 37 % were observed between preforms with and without the spray rubber adhesive. Moreover, predictions made through Darcy's law for resin front flow position with time are in good agreement with our experimental observations. Given this agreement between theory and experiments, we identify that the average longitudinal front flow velocity is directly proportional to the overall longitudinal preform permeability to porosity ratio (K/Ø). Our experimental observations suggest that the bonding between plies provided by the spray adhesive effectively increases the preform resistance to resin flow through two mechanisms 1) a reduction on the K/Ø ratio which in turn causes an increase on the resin front velocity at the top of the preform and reduces mold filling time, and 2) a simultaneous reduction on the through thickness permeability which in combination with the reduction on longitudinal permeability causes a larger delay in the resin flow front advance at the rigid mold with respect to the front advance at the top of the preform. Given these mechanisms for increased flow resistance, this paper closes with some cautionary comments regarding the possibility of detrimental effects on the mold filling and quality of the final product resulting from the use of the spray adhesive on thicker laminates.

Effective Impregnation of ε-Caprolactam with Polyamide 6 Oligomer in Thermoplastic Resin Transfer Molding

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Thermoplastic resin transfer molding of carbon fiber reinforced polyamide 6 composite with the improved processability using zeolite particle

Impregnation process of large-tow carbon-fiber woven fabric/polyamide 6 composites using solvent method

Optimal Polymerization Conditions in Thermoplastic-Resin Transfer Molding Process for Mechanical Properties of Carbon Fiber-Reinforced PA6 Composites Using the Response Surface Method

The Preparation of Monomer Casting Polyamide 6/Thermotropic Liquid Crystalline Polymer Composite Materials with Satisfactory Miscibility

Resin percolation and intimate contact in fast processing of thermoplastic composites

Interfacial Enhancement and Composite Manufacturing of Continuous Carbon-Fiber-Reinforced PA6T Composites via PrePA6T Ultrafine Powder

Evaluation of through-thickness permeability and the capillary effect in vacuum assisted liquid molding process

A General and Efficient Approach for the Dual-Scale Infiltration Flow Balancing in In Situ Injection Molding of Continuous Fiber Reinforced Thermoplastic Composites

Resin impregnation and interface property improvement of CFRP composite via modulating wettability of carbon fibers

Application of calcium carbonate in resin transfer molding process: An experimental investigation

Capillary Impregnation of Aligned Carbon Fiber Beds with Epoxy Resins

A Novel Synthetic Strategy for Preparing Polyamide 6 (PA6)-Based Polymer with Transesterification

Reproducibility Study of the Thermoplastic Resin Transfer Molding Process for Glass Fiber Reinforced Polyamide 6 Composites

Experimental Characterization of the Effect of a Spray Adhesive on the Velocity of Impregnation of a Resin on Carbon Fiber Fabrics Utilizing the VARTM Manufacturing Technique

Effect of Micro-Mold Cavity Dimension on Structure Andproperty of Polylactic Acid/Polycaprolactone Blend Undermicroinjection Molding Conditions

Kinetics of the Anionic Polymerization of Ε‐caprolactam from an Isocyanate Bearing Polystyrene

An approach to couple mold design and on-line control to manufacture complex composite parts by resin transfer molding

TRANSAMIDATION IN THE in Situ BLENDING OF POLYAMIDE 1212 WITH POLYAMIDE 6 THROUGH ANIONIC POLYMERIZATION OF CAPROLACTAM

In-situ spray impregnation of poly(pentamethylene oxamide) onto carbon fibers and their composites