Abstract:An in-situ compatibilized starch (St) and polyacrylonitrile (PAN) composite spinning solution was designed by preparing starch-graft-polyacrylonitrile (St-g-PAN) through graft copolymerizing acrylonitrile from soluble starch and using ammonium cerium nitrate (CAN) as initiator. As dimethyl sulfoxide (DMSO) was used as the solvent, St/St-g-PAN/PAN/DMSO spinning solution was prepared and St/St-g-PAN/PAN composite fibers were obtained by dry-wet spinning technique. The effects of air gap, coagulation bath, hot drawing and stretching, and thermal-setting process were studied in detail. Fourier transform infrared spectroscopy (FT-IR), solid state nuclear magnetic resonance (13C NMR), thermogravimetric analysis (TGA), X-ray diffraction analysis (XRD), and scanning electron microscopy (SEM) were used to characterize the structure and morphology of the copolymer and the fibers. Single fiber strength tester and sonic orientation instrument were performed to measure the fiber mechanical properties and orientation degrees. The results showed that as the grafting ratio ~150.0% and the reacting mixture containing St ~9.8%, St-g-PAN ~81.6%, and homo-PAN ~8.6% in DMSO solution with 6.0 wt% in concentration were used, the spinning parameters such as air gap ~35 mm, coagulation bath concentration ~70%, temperature ~25 °C, and positive stretching ~48%, hot drawing and stretching 6 times at 80 °C, thermal-setting at 90 °C for 3 h under constant length mode were met, composite fibers with breaking strength 3.41 cN·dtex−1, breaking elongation 14.41%, sonic orientation factor 0.625, moisture recovery ratio 10.53% under standard condition (1 atm, 22 °C, and relative humidity 65%), and boiling water shrinkage ratio 9.60% were obtained. The as prepared composite fiber was better than common viscose fiber 2.11 cN·dtex−1 and cotton fiber ~3.24 cN·dtex−1 and expected to be used in the fields of medical gauze, bandage, protective clothing, et al. besides of common textiles. The in-situ compatibilization method can be applied in preparation of other composite polymer materials.

Impregnation process of large-tow carbon-fiber woven fabric/polyamide 6 composites using solvent method

Interfacial Enhancement and Composite Manufacturing of Continuous Carbon-Fiber-Reinforced PA6T Composites via PrePA6T Ultrafine Powder

In-situ spray impregnation of poly(pentamethylene oxamide) onto carbon fibers and their composites

Effective Impregnation of ε-Caprolactam with Polyamide 6 Oligomer in Thermoplastic Resin Transfer Molding

Thermoplastic resin transfer molding of carbon fiber reinforced polyamide 6 composite with the improved processability using zeolite particle

Improved interfacial shear strength in carbon fiber enhanced semi-aromatic polyamide 6T composite via in-situ polymerization on fiber surface

Effects of fabrication method of composite yarn intermediate material and resin melt viscosity on the impregnation properties and mechanical properties of PA66 fiber and glass fiber composites

Processing of carbon fiber for 3D printed continuous composite structures

Improving the Interfacial Adhesion of Long Carbon Fiber-Reinforced Polyamide 6 Composites by Electrochemical Oxidation and Polyethylenimine-Carboxymethyl Cellulose Grafting

Structure, Thermal, and Mechanical Behavior of the Polysulfone Solution Impregnated Unidirectional Carbon Fiber Yarns

Polydopamine particle in-situ assisted carbon fiber/CNTs brush with dynamic imine bonds for enhancing the interface properties of its polyamide 6 composites

In-situ compatibilized starch/polyacylonitrile composite fiber fabricated via dry-wet spinning technique

Fabrication of carbon fiber/polyamide 6 composites with water resistance and anti-icing performance using a superhydrophobic fluorinated-polydopamine coating

An Evaluation of the Beneficial Effects of Polyamide 6's Thermal Stabilization by Ferric Chloride Complexation as a Novel Carbon Fiber Precursor

Multiphysics Coupling Study on Impregnation Process of Hot-Melt Resin in Fiber Fabrics for Composite Material Production

Capillary Impregnation of Aligned Carbon Fiber Beds with Epoxy Resins

Reinforcement of polyamide 6 with carbon fiber surface modified by a polar cross-linked network interfacial phase

Lab‐scale manufacturing of thermoplastic matrix‐continuous carbon fiber filaments for additive manufacturing: Melt impregnation, properties of the filaments and its printed composites

Manufacturing and characterization of continuous carbon fiber reinforced polyphenylene sulfide filaments via melt impregnation method

Improving interfacial adhesion and mechanical properties of carbon fiber reinforced polyamide 6 composites with environment-friendly water-based sizing agent

Continuous spinning of a single-walled carbon nanotube-nylon composite fiber