Abstract:Journal of Composite Materials, Ahead of Print. This study presents an investigation into mechanical and thermal properties, as well as the microstructure of Automated Fiber Placement-manufactured laminates using a novel carbon fiber-reinforced low-melt polyaryl ether ketone polymer material. The material's lower melting temperature and lower melt viscosity as compared to established high-temperature thermoplastic materials as PEEK, promises favourable characteristics for the Automated Fiber Placement process. This work aims at in-situ consolidation and the influence of a heated tooling and a post process tempering step, which both turned out to be promising in previous investigations. Laminates were manufactured using a cold tooling, a heated tooling configuration, a cold tooling with a subsequent tempering process step and a hot-pressed reference laminate. Differential Scanning Calorimetry showed that crystallinity values more than doubled for the heated tooling and post process tempering configurations, compared to the cold tooling, reaching 24% and 30%, respectively. Mechanical strength values showed an increase in interlaminar shear strength and compression strength but did not increase to the same extent as was expected from the increase in crystallinity. With Scanning Electron Microscopy differences in the microscopic structure of the polymer matrix could be detected. While the post process tempering step leads to a mostly lamellar crystalline structure, the heated tooling configuration and the post process hot pressing induce a predominance of crystalline spherulites, which might positively affect the mechanical performance. Computed Tomography scans revealed a high amount of porosity in the in-situ-manufactured samples and unprocessed tape material, which likely mitigated the positive effect of increased crystallinity.

In-situ spray impregnation of poly(pentamethylene oxamide) onto carbon fibers and their composites

Fully Aminated Rigid‐rod Aromatic Polyamide Efficiently Reinforces Tetraglycidyl Diamino Diphenyl Methane Epoxy Resin and Its Carbon Fiber Composite

Molecular-level Dispersion of Rigid-Rod Sulfonated Aromatic Polyamides in Epoxy Resin for Extraordinary Improvement in Both Strength and Toughness

New Reactive Rigid-Rod Aminated Aromatic Polyamide for the Simultaneous Strengthening and Toughening of Epoxy Resin and Carbon Fiber/epoxy Composites

Improved interfacial shear strength in carbon fiber enhanced semi-aromatic polyamide 6T composite via in-situ polymerization on fiber surface

Interfacial Enhancement and Composite Manufacturing of Continuous Carbon-Fiber-Reinforced PA6T Composites via PrePA6T Ultrafine Powder

Rapid and Scalable Synthesis of Novel Carboxylated Aramid Nanofibers for Simultaneously Improving the Strength and Toughness of Carbon Fiber/epoxy Laminates

Carbon fiber surface treatment for improved adhesion and performance of polydicyclopentadiene composites synthesized by ring opening metathesis polymerization

Preparation of self‐emulsifying waterborne polyamide‐imide sizing for carbon fiber and improvement on mechanical performances of carbon fiber reinforced thermoplastic polymer

Impregnation process of large-tow carbon-fiber woven fabric/polyamide 6 composites using solvent method

Improving the Interfacial Adhesion of Long Carbon Fiber-Reinforced Polyamide 6 Composites by Electrochemical Oxidation and Polyethylenimine-Carboxymethyl Cellulose Grafting

Preparation of Poly(Phenylene Oxide)/Polyamide-6 Nanocomposites with High Tensile Strength and Excellent Impact Performance

Polydopamine particle in-situ assisted carbon fiber/CNTs brush with dynamic imine bonds for enhancing the interface properties of its polyamide 6 composites

In Situ Polymerization Approach to Multiwalled Carbon Nanotubes Reinforced Polyundecanoylamide Composites

A simple synthesis of supramolecular Polyamide12 via solid‐state melt reaction and its interlaminar properties in Carbon Fiber Reinforced Thermoplastics

The Injected Foaming Study of Polypropylene/Multiwall Carbon Nanotube Composite with In Situ Fibrillation Reinforcement

Characteristics of in-situ automated fiber placement carbon-fiber-reinforced low-melt polyaryl ether ketone laminates part 1: Manufacturing influences

Improving carbon fibre reinforced polyphenylene sulfide using amine and phenolic interphase modifications

The effect of electrophoretic deposition p‐aminobenzenesulfonamide grafted CNT on mechanical properties of carbon fiber filled polyamide 6 composite

Reinforcement of polyamide 6 with carbon fiber surface modified by a polar cross-linked network interfacial phase

Molding process and properties of polyimide-fiber-fabric-reinforced polyether ether ketone composites