Abstract:Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Ahead of Print. Joints used in the automotive industry are widely manufactured by forging. A cold upsetting process can provide burr-free forging which reduces economic loss by preventing material waste. In this study, finite element simulations for the upsetting of a torque rod joint made of 41Cr4 steel are performed. The novelty of the present study lies in the fact that the upsetting performance is investigated through simulation having hardening model in order to replace the existing forging process. The performance of hardening models is studied for an accurate simulation and optimum parameters are determined. A combination of the bilinear isotropic hardening rule and Chaboche's nonlinear kinematic hardening rule is employed with the associated flow rule and Hill48 yield criterion to set up a plasticity model of the upsetting process for the first time. The parameters of the bilinear isotropic hardening rule are determined from monotonic tensile tests. The Chaboche's parameters are determined by using hysteresis loops obtained from strain-controlled low-cycle fatigue tests. The parameters of both rules are combined. Furthermore, they are calibrated using inverse analysis based on the optimization method. Genetic algorithm is used for optimization. The experimental diameter and height measurements of the joint are compared with those obtained from the optimized model. The results show that the application of the combined hardening rule provides better prediction performance of the upset dimensions with minimum dimensional tolerance. The calibrated parameters are presented for the upsetting process. The calibrated parameters of the combined hardening model for the upsetting are YS = 446.64 MPa, TM = 3363.05 MPa, C1 = 452.31 MPa, γ1 = 55.165, C2 = 212.13 MPa, γ2 = 12.24, C3 = 194.191 MPa, γ3 = 10.00 where [math] are hardening models' parameters. Absolute percent true error (APE) is 0.19%. The parameters are YS = 1.93 MPa, TM = 6.98 MPa, C1 = 580.79 MPa, γ1 = 1.08, C2 = 597.23 MPa, γ2 = 0.98, C3 = 565.05 MPa, γ3 = 2.87 in the case of cyclic load. APE is 1.66%. Also upsetting force requirement and material flow path are presented. The forging process can be replaced by the burr-free upsetting process with necessary changes in the die and press bench design. This replacement will save the 128-gr material per each one of the torque rod joint part.

Effect of shearing on production stability and die life in automatic multi-stage cold forging of an automobile wheel nut

Ejector pin-related high-cycle fatigue fracture of the critical die corner during automatic multistage cold forging of an automotive wheel nut

On the Size Effects in Micro/meso Semisolid Extrusion–forging of A356 Aluminum Alloy

Effect on the physical field of the die during the backward extrusion process of magnesium alloy wheel

SIMULATION ANALYSIS OF WHEEL BEARING FORGING PROCESS BASED ON DEFORM

Numerical Simulation of Pre-forging for Connecting Rod of Automobile Engine and Optimization of Its Pre-forging Billet

Automatic Multi-Stage Cold Forging of an SUS304 Ball-Stud with a Hexagonal Hole at One End

ON FORGING FORMING FORCE IN THE COMPOSITE TECHNOLOGY OF CROSS WEDGE ROLLING ( CWR ) AND FORGING FOR UNIVERSAL JOINT FORK

Development of smart cold forging die life cycle management system based on real-time forging load monitoring

Cylindrical Billet Size Optimization for Hot Closed-Die Forging of the Upper Ball Joint

Multi-scale numerical investigation of deep drawing of 6K21 aluminum alloy by crystal plasticity and a stress-invariant based anisotropic yield function under non-associated flow rule

Evolution of the microstructure and mechanical properties of interstitial-free steel during multi-axial diagonal forging

Tribological performance of additive-manufactured aluminum alloy—effect of post-weld cold deformation

Calibrating the combined hardening rule parameters for burr-free forging simulation of the torque rod joint

Multi-objective optimization of forging surface structure parameters of radial forging die with cycloidal

Effect of Deformation Degree on Microstructure and Properties of Ni-Based Alloy Forgings

Research and Application of Precision Forging Forming Process for Flat Thin Flash of Automobile Disc Steering Knuckle

Effect of Rotary Swaging on Mechanical Behaviors of Axle Steel Rod

Microstructure evolution and mechanical anisotropy of M50 steel ball bearing rings during multi-stage hot forging

Effect of Cold Pressing Deformation on Microstructure and Residual Stress of 7050 Aluminum Alloy Die Forgings

Enhancing the Robustness of Rib-Groove Filling and Strain Homogeneity in the Isothermal Forging of Titanium Alloy Multi-Rib Components