Abstract:Corrosion is a massive disaster in many sectors that caused the loss of billions of dollars. For example, it was reported that the total direct estimated cost of corrosion was about $ 276 billion in 1998 in the US, which is 3.1% of the nation's GDP. Therefore, a necessity to develop methods to overcome this challenge arose in the last few decades. Thus, the development of corrosion resistive coatings is significantly attracted researchers' attention. In combination with the corrosion inhibitors, organic and conversion coatings are used to improve the corrosion resistance of high-strength Al alloys. However, many corrosion inhibitors are carcinogenic: Chromate conversion coating performed very well, but alternative options need to be explored due to restrictions on its applications due to the health and environmental regulations. Moreover, organic coatings provide good corrosion resistance, but poor wear resistance and mechanical damage lead to corrosion issues. Metallic coatings are an alternative, and galvanized steel is one of the prominent examples. However, metallic coatings produced by elements such as Cr, Ni, Ti, or Ta are noble for Al or Mg-based alloys. Therefore, in any event of coating breakdown, the substrate would be more active and act as an anode and, corrode rapidly by galvanic interaction. Thus, such metallic coatings produced by the above-mentioned corrosion resistance elements are not very attractive for Al alloys. We present a sacrificial metallic coating with outstanding corrosion resistance. Al was alloyed with V using high-energy ball milling (HEBM) which enabled the formation of a superstrated solid solution of V in Al. Al-V alloy powder produced by HEBM was used for coating the high-strength substrate using cold spray. The corrosion behavior and corrosion mechanisms of cold sprayed specimens were investigated using advanced electrochemical and analytical techniques. The cold sprayed specimens exhibit high pitting potential, low corrosion current density, and a less noble corrosion potential than the substrate. This indicates that in any event of coating breakdown, the coating would corrode (i.e., act as a sacrificial anode) and prevent the substrate from corrosion. Alloy composition is chosen such that corrosion of coating releases chemical species that could inhibit corrosion by decreasing the cathodic efficiency of the substrate.

High performance aluminized Monel coatings with prolonged corrosion resistance in saline environment

The Effect of Ni201 Transition Layer on the Corrosion, Wear and Synergetic Cavitation Erosion-Corrosion Behavior of CMT-Monel K500 Coating

High-Temperature Corrosion of APS- and HVOF-Coated Nickel-Based Super Alloy under Air Oxidation and Melted Salt Domains

Corrosion Performance of Nano-Alumina Coatings over Anodized Aluminum Alloy by Dip Coating Method

Salt spray corrosion behavior and electrochemical performance of Al and Ti reinforced Ni60 coating by laser cladding

Erosion-corrosion behavior of Ni-Al-Cu coating on nickel-aluminium bronze alloy in 3.5 wt.% NaCl solution

Corrosion behaviour of iron and nickel aluminide coatings under the synergistic effect of NaCl and water vapour

Revealing Microstructure and Electrochemical Corrosion Behaviour of CoNiCrAlY Coatings Fabricated by Supersonic Plasma Spraying

Effects of Al content on the mechanical properties and corrosion behavior of Ni-Al coatings on 310S heat-resistant steel for CSP plants

Electrochemical and hot corrosion behaviour of annealed AlCoCrFeNi HEA coating over steel

The Microstructure of Aluminide Coatings on 310S and 347H Steels Formed by Pack Aluminizing and Their Corrosion Behavior in Molten Chloride Salts

Influence of Al contents on the long-term corrosion behaviors of cold-sprayed Zn-xAl coatings

Corrosion-Resistant Sacrificial Metallic Coatings Produced By Cold-Spray for Al Alloys

Sol–Gel-Derived Ni3Al Coating on Nickel Alloy for Oxidation Resistance in Supercritical Water Environments

Corrosion performance of slurry aluminide coatings in molten NaCl–KCl

Corrosion Behavior of High-Pressure Cold-Sprayed Zn30Al Alloy Coating on Q235 Steel

Cavitation erosion/corrosion synergy and wear behaviors of nickel-based alloy coatings on 304 stainless steel prepared by cold metal transfer

Corrosion Behavior of Ni-P-Nano-Al2o3 Composite Coating in the Presence of Anionic and Cationic Surfactants

Catechol/m-Phenylenediamine Modified Sol–Gel Coating with Enhanced Long-Lasting Anticorrosion Performance on 3003 Al Alloy

Evaluation of aluminum coatings in simulated marine environment

Impact of molten salts composition on the corrosion behavior of NiMoCr and CoNiCrAl coatings on L-PBF 316L stainless steel for CSP plants