Abstract:Fine-grained metals have attracted much interest due to the possibility to obtain both high strength and high ductility.Studies of the deformation mechanisms in fine-grained metals are therefore important,and can also help fill a gap in knowledge between nano-grained metals and conventional coarse-grained metals,which is an area of both scientific and industrial interest.For such an investigation it is very important to use a starting material with a simple microstructure.For this purpose spark plasma sintering(SPS) has been used to prepare samples of fully dense,fine-grained Al with average grain sizes ranging from 0.8μm to 5.2μm,in a fully recrystallized condition,with equiaxed grains and a random texture.The microstructures and mechanical properties of these sintered finegrained Al samples have been studied using EBSD,TEM and compression testing.Based on these studies,relationships between the microstructure and mechanical properties have been established. The results show that the formation of deformation microstructure depends on grain size.During deformation,all grains in samples with an average grain size of 5.2μm show grain subdivision by dislocation boundary formation,though few grains in a sample with an average grain size of 0.8μm show dislocation boundary formation.The mechanical properties of fine-grained Al show a transition in behavior with decreasing average grain size.For samples with an average grain size of 1.3μm,stressstrain curves show yield drop phenomenon,attributed to source-limited hardening.For a sample with an average grain size of 0.8μm,the stress-strain curve shows only limited work-hardening after yielding,in agreement with the observation of the limited formation of dislocation boundaries inside grains during deformation.For a sample with average grain size of 5.2μm the average dislocation boundary misorientation angle increases more quickly than in deformed conventional coarse-grained Al deformed to the same strain,due to the effect of increased volume fraction of grain boundaries and oxide particles.The strength of the SPS-prepared Al samples is higher than found for samples with identical grain sizes prepared by thermo-mechanical deformation,due to the presence of oxide particles,and to source-limited hardening for samples with average grain sizes smaller than 1.3μm.

Mechanical Properties of Sintered Al–Sn–Fe Alloys

Effect Forging Temperature and Backpressure on the Nature of Plastic Flow, Structure, and Mechanical Properties of Sintered Al–40 Sn Alloy

Microstructures and Mechanical Properties of Engineered Short Fibre Reinforced Aluminium Matrix Composites

Tribotechnical Properties of Sintered Antifriction Aluminum-Based Composite under Dry Friction against Steel

Upset Forging Temperature Effect on Structure and Tribological Properties of Sintered Al–7Fe–38Sn Alloy

Metallic Iron or a Fe-Based Glassy Alloy to Reinforce Aluminum: Reactions at the Interface during Spark Plasma Sintering and Mechanical Properties of the Composites

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

Sintering of the ultrafine Ag-SnO2 powders prepared by electroless silver plating

Mechanical Properties of Cu70Fe30 (at%) Bulk Metastable Alloys Prepared by Mechanical Alloying and Spark Plasma Sintering

Pressure Sintering, Structure and Some Properties of SiC–Al Composite Materials

Hot extrusion of SiCp/Al-Cu composites: optimizing mechanical properties through microstructural control

The dynamic properties of SiCp/Al composites fabricated by spark plasma sintering with powders prepared by mechanical alloying process

Microstructures and Mechanical Properties of Sintered Fine-Grained Al

Study on the process and microstructure of Fe34Mn13.5Al3Cr7.5Ni alloy prepared by spark plasma sintering based on elemental powder

An Al-Al interpenetrating-phase composite by 3D printing and hot extrusion

Compaction and sintering characteristics of composite metal powders

Tailoring Compressive Strength and Absorption Energy of Lightweight Multi-Phase AlCuSiFeX (X = Cr, Mn, Zn, Sn) High-Entropy Alloys Processed via Powder Metallurgy

Effects of spark plasma sintering parameters on properties of Fe-based bulk amorphous alloys

A Micromechanical Analysis to the Viscoplastic Behavior of Sintered Silver Joints under Shear Loading

Effect of Pressure and Temperature on Densification in Electric Field-Assisted Sintering of Inconel 718 Superalloy

Graded Microstructure and Mechanical Properties of Spark Plasma Sintered Fe-Cr alloys