Abstract:The 2195 Al-Cu-Li alloy is widely utilized in the aerospace industry due to its lightweight nature and high strength. Consequently, gaining a comprehensive understanding of techniques to enhance its microstructural and mechanical properties is crucial for the consistent production of reliable and high-strength aerospace components. In this investigation, a pristine 2195 industrial ingot was subject to three distinct forging pretreatments: PT1, which involved a direct three upsetting and three stretching (3U3S) process; PT2, which combined double stage homogenization (DH) with 3U3S; and PT3, which involved DH along with six upsetting and six stretching (6U6S). Subsequent warm deformation and T8 aging treatment were applied to the pretreated forgings. The microstructure evolution during the processes and the final mechanical properties in three orthogonal dimensions were examined. The findings revealed that the combination of DH and multi-dimensional forging (MDF) facilitated the dissolution of non-equilibrium phases to a greater extent. Consequently, the main strengthening phase transformed from the T 1 + δ` phase observed in PT1 to the denser T1 + little θ` phase observed in PT2 and PT3 after T8 aging treatment. Notably, the tensile strength and yield strength of PT2 and PT3 specimens increased by 20-30 MPa in all three directions. Moreover, the MDF process accelerated the recrystallization behavior from PT1 to PT3, resulting in a gradual reduction in the average grain size of the pretreated samples from 356 μm to 186 μm. Following warm forging and T8 aging, the grains exhibited a finer and equiaxed structure. Additionally, the coarse phase was identified as the primary source of transgranular cracking. The coarse phases within the matrix became more homogeneous and finer from PT1 to PT3, with a gradual decrease in their area fraction. On the fracture surfaces, the aggregation of coarse phases diminished. Consequently, the elongation in the z-direction improved, and the elongation anisotropy and standard deviation decreased in all three directions for PT3 specimens. The findings presented in this study provide valuable insights into the high-performance manufacturing of Al-Cu-Li alloys.

Effect Forging Temperature and Backpressure on the Nature of Plastic Flow, Structure, and Mechanical Properties of Sintered Al–40 Sn Alloy

Upset Forging Temperature Effect on Structure and Tribological Properties of Sintered Al–7Fe–38Sn Alloy

Mechanical Properties of Sintered Al–Sn–Fe Alloys

Effect of Forging on Microstructure and Properties of Al-9Si-5Cu-0.2Zr-0.1Sr-0.16Ti-0.1Ce Cast Aluminum Alloy

The Effect of the Forging Process on the Microstructure and Mechanical Properties of a New Low-Cost Ti-5Al-1.5Mo-1.8Fe Alloy

Influence of Forging Temperature on the Microstructures and Mechanical Properties of a Multi-Directionally Forged Al–Cu–Li Alloy

Influence of Soaking Time on Microstructural, Machinability, and Mechanical Properties of Al-10Si-0.3Mg Alloy Fabricated by Direct Powder Forging

Effect of Deformation Degree on Microstructure and Properties of Ni-Based Alloy Forgings

The effects of hot forging on the preform additive manufactured 316 stainless steel parts

Structure, Mechanical and Physical Properties of Cu/Al–10% La Composite Produced by Rotary Forging

Effect of Rotary Forging on Microstructure and Mechanical Properties of Mg–3Al–1Zn Magnesium Alloy

Effects of multi-directional forging on the microstructure and mechanical properties of TiB2 particulate reinforced 6061Al composite

Tribotechnical Properties of Sintered Antifriction Aluminum-Based Composite under Dry Friction against Steel

Microstructure and Mechanical Properties of Sintered and Forged Fe-2Cu-0.5C-0.11S Materials

Characterization of Residual Stresses and Grain Structure in Hot Forging of GH4169

Microstructures and mechanical properties during sinter-forging of a novel TiAl alloy

Improving strain hardening behavior in nano-intermetallic reinforced aluminum in-situ composites through an optimized twostep thermal processing method; sintering and uniaxial forging

Influence of hot forging on grain formation in Al0.35CoCrFeNi high-entropy alloy: numerical simulation, microstructure and mechanical properties

Impact Fracture Behaviour of Powder Metallurgy Steels Sintered at Different Temperatures

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

The Influence of Physical Properties of C55 Alloy on Geometry of Flow in the Process of Shaping