Abstract:The present work is focused on the multidirectional forging (MDF) of Al–20 wt-% Si alloys with the addition of refiners and modifiers. The MDF process was performed at 200°C with a cumulative strain of 0.63. Microstructural characterization and mechanical performance were evaluated on the Al–20Si, Al–20Si–4.5Cu, Al–20Si–4.5Cu–1(Al–Ti–B), Al–20Si–4.5Cu–1(Al–Ti–B)–10(Al–Sr). The microstructure analysis revealed significant changes in the eutectic and primary phase refinement. The micro-Vickers hardness confirmed that the MDF process resulted in increased hardness (125 ± 1.9 VHN) compared to the homogenized samples (96 ± 2.7 VHN). Tensile test results showed that with the accumulation of strain, ultimate tensile strength increased to 435 MPa from 302 MPa with reduction in the percentage of elongation from 7.8 to 5.6. The grains were more uniformly distributed with addition of modifiers, and refiners further reduced the nucleation number of eutectic grains. The wear study demonstrated that the wear resistance is more in the Al–Si-Cu-Sr sample due to the increased level of hardness. The combination of multidirectional forging techniques with judicious incorporation of refiners and modifiers engenders a synergistic enhancement of microstructural integrity, hardness profiles, and wear-resistant properties in hypereutectic Al-20Si alloys. Le travail courant se concentre sur le forgeage multidirectionnel (MDF) des alliages Al-20% en poids Si avec ajout d'agents d'affinage et modificateurs. On a réalisé le procédé MDF à 200°C sur trois passes avec une déformation cumulée de 0.63. Suite au procédé MDF, on a évalué la caractérisation microstructurale et les performances mécaniques sur Al–20Si, Al–20Si–4.5Cu, Al–20Si–4.5Cu–1(Al–Ti–B) et Al–20Si–4.5Cu–1(Al–Ti–B)–10(Al–Sr). L'analyse de la microstructure a révélé des changements significatifs dans le raffinement de la phase eutectique et primaire après le traitement MDF. Les essais de microdureté Vickers ont confirmé que le procédé MDF entraînait une dureté accrue (125 ± 1.9 VHN) par rapport aux échantillons homogénéisés (96 ± 2.7 VHN). Les résultats des essais de traction ont montré qu'avec l'accumulation de déformation, la résistance ultime à la traction a augmenté de 302 MPa à 435 MPa avec une réduction du pourcentage d'allongement de 7.8 à 5.6. Les grains étaient distribués plus uniformément avec l'ajout d'agents modificateurs, et les agents d'affinage ont réduit davantage le nombre de nucléation des grains eutectiques. L'étude d'usure a démontré que la résistance à l'usure est supérieure dans l'échantillon Al–Si–Cu–Sr en raison du niveau de dureté accru. La combinaison des techniques de forgeage multidirectionnel avec l'incorporation judicieuse d'agents d'affinage et modificateurs engendre une amélioration synergique de l'intégrité microstructurale, des profils de dureté et des propriétés de résistance à l'usure des alliages hypereutectiques Al–20Si.

Influence of Soaking Time on Microstructural, Machinability, and Mechanical Properties of Al-10Si-0.3Mg Alloy Fabricated by Direct Powder Forging

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Influence of Forging Temperature on the Microstructures and Mechanical Properties of a Multi-Directionally Forged Al–Cu–Li Alloy

Effect of Multidirectional Forging on the Microstructures and Mechanical Properties of the Al–Mg–Si Alloy

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

Mechanical alloying and direct powder forging of Ni–20Cr–20Fe-0.08C alloy

Effect of Forging on Microstructure and Properties of Al-9Si-5Cu-0.2Zr-0.1Sr-0.16Ti-0.1Ce Cast Aluminum Alloy

The Effect of the Forging Process on the Microstructure and Mechanical Properties of a New Low-Cost Ti-5Al-1.5Mo-1.8Fe Alloy

Effect of Rotary Forging on Microstructure and Mechanical Properties of Mg–3Al–1Zn Magnesium Alloy

Microstructure, Texture, Mechanical Properties, and Corrosion Behavior of Biodegradable Zn-0.2Mg Alloy Processed by Multi-Directional Forging

Effect of multidirectional forging on grain structure and mechanical properties of hypereutectic Al–20%Si alloys with added refiners and modifiers

Microstructural evolutions and mechanical properties of 6082 aluminum alloy part produced by a solution-forging integrated process

The effects of hot forging on the preform additive manufactured 316 stainless steel parts

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

In-situ alloying of Ti-5Fe titanium alloy using direct powder forging and the effect of the powder mixing method

Effect of Deformation Degree on Microstructure and Properties of Ni-Based Alloy Forgings

Microstructure, texture and mechanical properties of 0.4GNPs‐Mg‐8Al‐1Sm composites prepared by pulse current‐assisted multi‐directional forging

Effect of Multidirectional Isothermal Forging on Microstructure and Mechanical Properties in Ti-6Al-4V Alloy

Microstructure and mechanical properties of in situ TiB 2 •TiAl 3 /2024Al composite subjected to multidirectional forging

Markedly enhancing mechanical properties of powder metallurgy superalloy by hot oscillatory forging

The Effect of Multidirectional Forging on the Microstructure and Superplasticity of the Al–Mg–Si–Cu System Alloys with Different Contents of Mg and Si