Abstract:Alveolar bone loss and insufficient bone mass are major obstacles to the oral implant treatment. Guided bone regeneration (GBR) is an effective and widely used method to solve this problem. Titanium mesh with good 3D space maintenance ability shows excellent effect in the assistance of GBR. Unfortunately, such metal mesh needs to be removed by secondary operation, and the exposure after operation can't be completely avoided. Thus, it is a big challenge to repair the alveolar bone defects with different shapes and sizes by customization. Herein, the wollastonite bioceramics without and with 6% magnesium doping (CSi, CSi-Mg6) were prepared to fabricate the macroporous dome-like meshes with different CSi/CSi-Mg6 mass ratio (0:100, 16:84, 32:68) via digital light processing-based 3D printing (DLP) technique. The mechanical parameters, biodegradable rate and osteogenic stem cell viability in vitro of the bioceramic scaffolds with different morphologies were also evaluated systematically. The macroporous bioceramic dome- or titanium mesh-assisted osteogenic potentials in the calcined bone granules were evaluated in the rabbit calvarial bone defect models. The experimental results showed that the scaffolds with 16%CSi exhibited satisfactory mechanical properties and promoted the proliferation and differentiation of osteogenic stem cells. The bioactive domes displayed significantly higher osteostimulate activity than the metal mesh in the calcined bone mineral granule systems. The appreciable CSi-Mg6 content (>= 84%) in the dome scaffolds could maintain the porous structures after 16 weeks of implantation, and especially the presence of 16% CSi in the bioceramic dome may greatly balance the scaffold biodegradation and restoration treatment. Totally, the 3D printed nonstoichiometric wollastonite-based scaffolds are expected to be the promising candidates to replace titanium mesh in GBR.

Fabrication of 3D printed Ca3Mg3(PO4)4-based bioceramic scaffolds with tailorable high mechanical strength and osteostimulation effect

3D-Printed Bioceramic Scaffolds with High Strength and High Precision

3D Printed High-Strength Bioceramic Dome Scaffolds with Controllable Biodegradation for Guided Bone Regeneration

Effect of Foreign Ion Substitution and Micropore Tuning in Robocasting Single-Phase Bioceramic Scaffolds on the Physicochemical Property and Vascularization

3D Printed Long-Term Structurally Stable Bioceramic Dome Scaffolds with Controllable Biodegradation Favorable for Guided Bone Regeneration

3D Printing Novel Porous Granule-Type Bioceramics Via Magnesium Tuning Biological Performances Beneficial for Implantation and Clinical Translation

3D robocasting magnesium-doped wollastonite/TCP bioceramic scaffolds with improved bone regeneration capacity in critical sized calvarial defects

3D Printing Magnesium-Doped Wollastonite/β-Tcp Bioceramics Scaffolds with High Strength and Adjustable Degradation

Ultrahigh Strength of Three-Dimensional Printed Diluted Magnesium Doping Wollastonite Porous Scaffolds

Tuning filament composition and microstructure of 3D-printed bioceramic scaffolds facilitate bone defect regeneration and repair

Custom Repair of Mandibular Bone Defects with 3D Printed Bioceramic Scaffolds

3D Printing Bioceramic Porous Scaffolds with Good Mechanical Property and Cell Affinity

Sintering densification mechanism and mechanical properties of the 3D-printed high-melting-point-difference magnesium oxide/calcium phosphate composite bio-ceramic scaffold

369Fabrication of 3D gel-printed β-tricalcium phosphate/titanium dioxide porous scaffolds for cancellous bone tissue engineering

Fabrication of 3D gel-printed β-tricalcium phosphate/titanium dioxide porous scaffolds for cancellous bone tissue engineering

Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect

Improvement in mechanical strength and biological function of 3D-printed trimagnesium phosphate bioceramic scaffolds by incorporating strontium orthosilicate

Nonstoichiometric wollastonite bioceramic scaffolds with core-shell pore struts and adjustable mechanical and biodegradable properties

3D printing of PCL-ceramic composite scaffolds for bone tissue engineering applications

3D‐Printed Bioceramic Scaffolds Reinforced by the In Situ Oriented Growth of Grains for Supercritical Bone Defect Reconstruction

Fabrication and properties of CaSiO3/ Sr3(PO4)2 composite scaffold based on extrusion deposition