Abstract:The structure of energy rotor components includes different structural materials in the sections, which are subjected to varying levels of thermal loading. The first component section has to include a precipitation-hardened nickel-based alloy, while the second one may be manufactured from other materials. Due to the installation cost, the use of expensive nickel-based materials is not recommended for applications in sections with a lower degree of thermal loading. Therefore, this aspect is still actually from an engineering point of view and is discussed in the paper by means of manufacturing and experimental approaches. The paper follows the welding problems related to a hybrid joint made of superalloy (Alloy 59) and hard rusting steel (S355J2W+N steel). The problem is solved using the MIG process at various parameters. With respect to the joint quality, microstructural features and mechanical parameters of the examined zone are presented. In the case of microstructure analysis, the dendritic and cellular natures of austenite were dominant elements of the joint. Mechanical tests have expressed a 50% reduction in elongation of the steel and alloy steel weld and lowering mechanical parameters. Mechanical parameters of the joint were on the level of their values observed for the steel, while the hardening coefficient followed the hardening curve of the alloy. Decohesion of the steel and mixed weld has reflected the constant proportion of values of axial and shear stress components up to the total separation. It is noted the tensile curves of the alloy and alloy steel joint follow a very similar shape, reporting the same response on the monotonic tension. The materials can be analysed by applying constitutive equations at very similar values of their coefficients. The obtained results enabled elaborating and examining the MIG welding process for thick-walled structures (not smaller than 8 mm) in detail giving all parameters required for technology. Finally, the technology for producing a hybrid joint using difficult-to-weld materials with different physical and mechanical properties, such as nickel alloys and low-alloy steels, is proposed. Results have shown it possible to develop a technology for producing of hybrid joints (supper alloy + hard rusting steel) with assumed physical and mechanical properties for rotors applied in the power boiler. This solution was proposed instead of previously used elements of rotors from expensive materials. It was assumed that the newly proposed and utilised method of welding will allow for obtaining good properties in terms of energy devices.

Joining of the functionally gradient friction material to the backing plate for wind turbines using sinter-brazing technique

Development of functionally gradient Cu-Fe based sintered brake pad materials

Comparative study of sintered and composite brake pad for wind turbine applications

Tribological Performance of the Continuous Steel Fiber-reinforced Cu based Friction Material for Heavy-duty Braking Applications

Study and Optimization of Metal Based Sintered Materials for Automotive Brake Friction Production

Friction-increasing mechanism of contact pair using different surface treatment processes

Thermal behavior analysis and mechanical characterization of friction stud welded AISI 304/AA6063 joints

Backing plate material selection for optimizing joint performance in friction stir welded aluminium honeycomb

Microstructure and Mechanical Properties of Solid-State Rotary Friction Welded Inconel 713C and 32CrMo4 Steel Joints Used in a Turbocharger Rotor

Impact of Backing Plate and Thermal Boundary Conditions for High-Speed Friction Stir Welding of 25-mm Thick Aluminum Alloy 7175-T79

Thermomechanical analysis of hybrid friction composite material and its correlation with friction braking performance

Friction forge riveting: A new joining method for connecting 40Cr steel and TC4 titanium alloy

INFLUENCE OF MOISTURE CONDITION AND SILICA SAND ON FRICTION COEFFICIENT OF WIND TURBINE BRAKE SYSTEM

Enhancement of joint strength of dissimilar aluminum/polymer hybrid joints by friction stir spot welding by surface textures

Thermal-Fluid-Solid Coupling Mechanism of a Novel Friction Reduction Cooling Structure for Gas Turbine

Testing and evaluation on friction surfacing of Alloy 36 over spheroidal graphite iron and its effect on coating thickness and width using artificial neural networks and response surface methodology

Friction self-riveting welding between polymer matrix composites and metals

A Study of Tribological Phenomena in Friction Couple: Brake Composite Material—Steel

Superalloy-Steel Joint in Microstructural and Mechanical Characterisation for Manufacturing Rotor Components

Hybrid Joining of Dissimilar Thin Metallic Sheets—Mechanical Joining and Adhesive Bonding

Friction stir welding of high-strength steel