Abstract:The billets of interstitial-free (IF) steel are deformed by equal-channel angular pressing (ECAP) at 298 K (25 °C) adopting the route BC up to an equivalent strain (εvm) of 24. The evolution of microstructures and their effects on the mechanical properties are examined. The microstructural refinement involves the elongation of grains, the subdivision of grains to the bands with high dislocation density, and the splitting of bands into the cell blocks and then cell blocks into the cells. The widths of the bands and the size of cells decrease with strain. The degree of reduction in the grain size is highest at the low strain level. However, most of the boundaries at this stage are of low-angle boundaries (at εvm = 3). Thereafter, the misorientation angle increases by progressive lattice rotation with strain. The coarse bands transform step by step from the lamellar structure to the ribbon-shaped grains and finally to the near-equiaxed grain structures with the subgrains of a saturated low-angle grain boundary fraction of 0.34 at very large strain >15. The as-received coarse-grained microstructure (grain size of 57.6 ± 21 µm) has been refined to 257 ± 48 nm at an equivalent strain of 24. The strength increases considerably up to εvm = 3 due to grain refinement and high dislocation density. However, the strengthening at later stages is mainly due to the increase in misorientation angle and refinement. Initial yield strength of 227 MPa is increased to a record value of 895 MPa on straining up to εvm = 24 at 298 K (25 °C). Uniform elongation decreases drastically at low equivalent strain but it regains marginally later. The ECAPed sample fails by a ductile fracture at εvm = 0.6 to 6 but by a mixed mode of ductile–brittle fracture at larger strain of 9 to 24.

Microstructure and mechanical properties of ultrafine grained IF steel processed by equal channel angular pressing

Microstructure and mechanical properties after annealing of equal-channel angular pressed interstitial-free steel

Annealing behaviour and mechanical properties of severely deformed interstitial free steel

Ultra-High-Strength Interstitial-Free Steel Processed by Equal-Channel Angular Pressing at Large Equivalent Strain

Grain Refinement and Strengthening of an Aluminum Alloy Subjected to Severe Plastic Deformation through Equal-Channel Angular Pressing

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

Effect of the Equal Channel Angular Pressing on the Microstructure and Phase Composition of a 7xxx Series Al-Zn-Mg-Zr Alloy

Mechanical properties of iron processed by severe plastic deformation

Mechanical responses, texture and microstructural evolution of high purity aluminum deformed by equal channel angular pressing

Three-Dimensional Microstructures and Tensile Properties of Pure Iron During Equal Channel Angular Pressing

Three-dimensional numerical analysis and experimental investigation of grain refinement in multi-pass equal channel angular pressing for round-workpieces

Microstructure Evolution in High Purity Aluminum Single Crystal Processed by Equal Channel Angular Pressing (ECAP)

Microstructural evolution and mechanical properties of AZ31 Mg alloy fabricated by a novel bifurcation-equal channel angular pressing

Ebsp Investigation of Microstructure and Texture Evolution During Equal Channel Angular Pressing of Aluminium

Microstructural evolution and mechanical properties of accumulative roll bonded interstitial free steel

Investigating the Influence of Thermomechanical Equal Channel Angular Pressing (ECAP) Improved Die on AA-6061

Structural Characterization of Binary Al-Cu Alloy Processed by Equal Channel Angular Pressing at Half of the Melting Point

Effect of original microstructure on microstructure and properties of pure copper subjected to equal channel angular pressing(ECAP)

Microstructure evolution and mechanical properties of Mg–Mn–RE alloy processed by equal channel angular pressing

Grain Refinement and Texture Change in Interstitial Free Steels after Severe Rolling and Ultra-Short Annealing

Mechanical Properties and Microstructure of AZ31 Magnesium Alloy Processed by Intermittent Ultrasonic-Assisted Equal Channel Angular Pressing