Abstract:A thorough numerical investigation was carried out to examine the heat transfer characteristics within a rectangular channel integrated with metal foam blocks for solar air heating applications. The study employed numerical simulations using the extended Darcy–Forchheimer model with the assumption that there exist local thermal nonequilibrium conditions within the porous foam region. Four configurations, denoted as P–A, P–P, A–P, and A–A, were explored based on the presence or absence of foam blocks relative to the heated section. The study meticulously analyzed the influence of key parameters, such as the number of foam blocks (N = 1–5), permeability (quantified by pore density, ω = 10 ‐ 30 PPI ), and Reynolds number (Re = 4000 ‐ 16 , 000 ), on the thermohydraulic performance. The results were promising, indicating a significant increase in the average Nusselt number (Nu ) with the inclusion of foam blocks, albeit accompanied by an undesirable increase in the friction factor. Among the various configurations, the P–A arrangement, where porous blocks are situated at the entrance of the heating channel, exhibited superior thermal performance. Furthermore, the optimal heat transmission rate was attained with a single porous block (N = 1) in the P–A configuration, at a Reynolds number of 16,000 and high permeability (ω = 10 PPI ). Conversely, the maximum friction factor was observed with five porous blocks (N = 5) in the A–P configuration, at a Reynolds number of 4000 and low permeability (ω = 30 PPI ). The exhaustive analysis of thermohydraulic performance was evaluated using the performance evaluation criterion (PEC), which optimizes the trade‐off between increased heat transfer rate and consequent pressure loss. The P–A arrangement, particularly with higher permeability and a minimal number of porous blocks, demonstrated the highest PEC value of 2.71, representing a significant 171% improvement compared with an empty channel. This study underscores the effectiveness of strategically placing and optimizing metal foam blocks to improve the thermal performance of heat exchanger systems.

Wall Heat Transfer Characteristic of Parallel-plate Channel Filled with Open-cell Metal Foams in Large Flow Velocity Range

Air-side Performance of Open-Cell Metal Foams for Use in Dehumidifying Heat Exchangers

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Effects of channel flow blockage on metal foam heat transfer

Local heat transfer distribution of thermally developing region in a rectangular open-cell metal foamed channel

Pore-scale Simulation of Forced Convection Heat Transfer under Turbulent Conditions in Open-Cell Metal Foam

Enhanced heat transfer performance of optimized micro-channel heat sink via forced convection in cooling metal foam attached on copper plate

Unlocking the Thermal Efficiency of Irregular Open-Cell Metal Foams: A Computational Exploration of Flow Dynamics and Heat Transfer Phenomena

Numerical Study on Fluid Flow Behavior and Heat Transfer Performance of Porous Media Manufactured by a Space Holder Method

Experimental Study of Boiling Heat Transfer Characteristics of Metal Foam Porous-wall Mini-channels

Comparison of convective heat transfer in metal foam-filled channels of three different cross-sections

Pore-scale Simulation of Flow in Minichannels with Porous Fins

Analytical and Numerical Study on Thermally Developing Forced Convective Flow in a Channel Filled with a Highly Porous Medium Under Local Thermal Non-Equilibrium

Thermal management of power electronics with liquid cooled metal foam heat sink

Optimizing heat transfer within a rectangular channel through intermittent metal foam block configurations: A numerical study

Experimental study on heat transfer characteristics of flow on an inclined hot metal plate

Heat transfer enhancement in a counter-flow sinusoidal parallel-plate heat exchanger partially filled with porous media using metal foam in the channels’ divergent sections

Boundary conditions and wall effect for forced convection heat transfer in sintered porous plate channels

Numerical analysis of the heat transfer enhancement by using metal foam

Flow Boiling Heat Transfer in Copper Foam Fin Microchannels with Different Fin Widths Using R134a

Numerical Investigation of Fluid Flow and Heat Transfer in High-Temperature Wavy Microchannels with Different Shaped Fins Cooled by Liquid Metal