Abstract:We introduce magnetophoresis-based microfluidics for sorting biological targets using positive Magnetophoresis (pM) for magnetically labeled particles and negative Magnetophoresis (nM) for label-free particles. A single, externally magnetized ferromagnetic wire induces repulsive forces and is positioned across the focused sample flow near the main channel's closed end. We analyze magnetic attributes and separation performance under two transverse dual-mode magnetic configurations, examining magnetic fields, hydrodynamics, and forces on microparticles of varying sizes and properties. In pM, the dual-magnet arrangement (DMA) for sorting three distinct particles shows higher magnetic gradient generation and throughput than the single-magnet arrangement (SMA). In nM, the numerical results for SMA sorting of red blood cells (RBCs), white blood cells (WBCs), and prostate cancer cells (PC3-9) demonstrate superior magnetic properties and throughput compared to DMA. Magnetized wire linear movement is a key design parameter, allowing device customization. An automated device for handling more targets can be created by manipulating magnetophoretic repulsion forces. The transverse wire and magnet arrangement accommodate increased channel depth without sacrificing efficiency, yielding higher throughput than other devices. Experimental validation using soft lithography and 3D printing confirms successful sorting and separation, aligning well with numerical results. This demonstrates the successful sorting and separating of injected particles within a hydrodynamically focused sample in all systems. Both numerical and experimental findings indicate a separation accuracy of 100% across various Reynolds numbers. The primary channel dimensions measure 100 μm in height and 200 μm in width. N52 permanent magnets were employed in both numerical simulations and experiments. For numerical simulations, a remanent flux density of 1.48 T was utilized. In the experimental setup, magnets measuring 0.5 × 0.5 × 0.125 inches and 0.5 × 0.5 × 1 inch were employed. The experimental data confirm the device's capability to achieve 100% separation accuracy at a Reynolds number of 3. However, this study did not explore the potential impact of increased flow rates on separation accuracy.

Continuous Magnetophoretic Separation of Blood Cells from Plasma at the Microscale

Microfluidic Device for Continuous Magnetophoretic Separation of Red Blood Cells

Gravitational sedimentation induced blood delamination for continuous plasma separation on a microfluidics chip.

A Flyover Style Microfluidic Chip for Highly Purified Magnetic Cell Separation.

Microfluidic Separation of Particles from Whole Blood Using Shear Induced Diffusion

Continuous Inertial Microparticle And Blood Cell Separation In Straight Channels With Local Microstructures (Vol 16, Pg 532, 2016)

Blood component separation in straight microfluidic channels

High-throughput White Blood Cells (leukocytes) Separation and Enrichment from Whole Blood by Hydrodynamic and Inertial Force

Label-free blood cells separation and enrichment from whole blood by high-throughput hydrodynamic and inertial force

A Microfluidic Chip for Blood Plasma Separation Using Electro-Osmotic Flow Control

Design and Development of a Traveling Wave Ferro-Microfluidic Device and System Rig for Potential Magnetophoretic Cell Separation and Sorting in a Water-Based Ferrofluid

Continuous Flow Separation of Red Blood Cells and Platelets in a Y-Microfluidic Channel Device with Saw-Tooth Profile Electrodes via Low Voltage Dielectrophoresis

Design and Fabrication of a High Performance Microfluidic Chip for Blood Plasma Separation: Modelling and Prediction of System Behaviour via CFD Method

Enhanced microfluidic multi-target separation by positive and negative magnetophoresis

Tessellated permanent magnet circuits for flow-through, open gradient separations of weakly magnetic materials

Continuous Separation of Magnetic Beads Using a Y-shaped Microfluidic System Integrated with Hard-Magnetic Elements

Scalable high-throughput microfluidic separation of magnetic microparticles

Correlation of simulation/finite element analysis to the separation of intrinsically magnetic spores and red blood cells using a microfluidic magnetic deposition system

Blood–plasma Separation in Y-shaped Bifurcating Microfluidic Channels: a Dissipative Particle Dynamics Simulation Study

Capillary flow-driven microfluidic device with wettability gradient and sedimentation effects for blood plasma separation

Numerical Design of a Highly Efficient Microfluidic Chip for Blood Plasma Separation