Abstract:Additive manufacturing (AM) introduces unique grain feature and anisotropy in metals, as well as relatively poor surface quality, so the knowledge about the formation of post-machining-induced surface integrity needs to be extended. This study aims to understand the machining phenomena in orthogonal cutting of Inconel 718 produced via powder bed fusion of metals using a laser beam system (PBF-LB/M), paying particular attention to the cutting energy, chip formation, geometrical defects, and microstructural deformation. Experiments are conducted on both wrought (W 718) and PBF-LB/M (PBF 718) Inconel 718, whereby the cutting speed and the anisotropy of the workpiece in the raw state play an important role. The results indicate that less cutting energy is consumed when cutting PBF 718 in the direction perpendicular to its build direction (BD), followed by cutting in its BD. Denser shearing-induced slip lines and relatively continuous chip morphology are found when cutting PBF 718 in its BD, moreover, the effect of cutting speed on shearing deformation of columnar grains under this condition is analysed. More importantly, this study identifies a significant geometrical defect phenomenon which is unique to PBF 718 and highly depends on the cutting speed and anisotropy of grain feature. A detailed characterisation shows that this behaviour is caused by tearing within the grains in the matrix material and not by the presence of hard inclusions, which has rarely been reported in the literature. The microstructure in the subsurface area exhibits that the density of grain boundaries in the cutting direction plays the key role in plastic deformation, as the machining process mainly causes dragging behaviour in the area below the machined surface. Thus, cutting PBF 718 in the direction perpendicular to its BD shows similar deformation layer to W 718, while cutting PBF 718 in its BD displays much stronger subsurface deformation. The obtained results greatly help to understand the cutting phenomena in post-machining of additively manufactured Ni-based components, especially the integrity for a better functional surface.

On the role of energy input in the surface morphology and microstructure during selective laser melting of Inconel 718 alloy

Effect Of Heat Input Parameters On Temperature Field In Inconel 718 Alloy During Selective Laser Melting

Effect of Laser Energy Density on the Microstructure and Microhardness of Inconel 718 Alloy Fabricated by Selective Laser Melting

Understanding processing parameters affecting residual stress in selective laser melting of Inconel 718 through numerical modeling

Numerical and Experimental Investigation on Formation of Surface Structures in Laser Remelting for Additive-Manufactured Inconel 718

Impact of Laser Power and Scanning Velocity on Microstructure and Mechanical Properties of Inconel 738LC Alloys Fabricated by Laser Powder Bed Fusion

Effect of Layer-Wise Varying Parameters on the Microstructure and Soundness of Selective Laser Melted INCONEL 718 Alloy

Processing Correlations of Laser Direct Energy Deposited Inconel718 Based on Multi-Field Numerical Simulation

Relationship Between Energy Efficiency and Surface Morphologies in Micro-Milling of SLM Inconel 718

High-fidelity Numerical Model of Melt Pool Dynamics in Selective Multi-Laser Melting of Inconel 718 under Different Scanning Strategies

Effect of Laser Energy Density on the Microstructure, Mechanical Properties, and Deformation of Inconel 718 Samples Fabricated by Selective Laser Melting

Influence of Laser Parameters on Segregation of Nb During Selective Laser Melting of Inconel 718

Effects of laser scanning speed and building direction on the microstructure and mechanical properties of selective laser melted Inconel 718 superalloy

Mechanical properties and microstructure evolution of selective laser melting Inconel 718 along building direction and sectional dimension

Effect of Laser Power and Scanning Speed on the Microstructure and Mechanical Properties of SLM Fabricated Inconel 718 Specimens

Formability, Microstructure and Properties of Inconel 718 Superalloy Fabricated by Selective Laser Melting Additive Manufacture Technology

Numerical simulation and solidification characteristics for laser cladding of Inconel 718

Formation and evolution mechanisms of pores in Inconel 718 during selective laser melting: Meso-scale modeling and experimental investigations

Impact of Laser Scanning Speed on Microstructure and Mechanical Properties of Inconel 718 Alloys by Selective Laser Melting

The microstructural evolution and mechanical response of laser direct energy deposition Inconel 718 alloy based on simulation and experimental methods

On machining-induced surface integrity of Inconel 718 fabricated by powder bed fusion