Abstract:The anisotropy of the structure and properties caused by the strong epitaxial growth of grains during laser powder bed fusion (L-PBF) significantly affects the mechanical performance of Inconel 718 alloy components such as turbine disks. The defects (lack-of-fusion, LoF) in components processed via L-PBF are detrimental to the strength of the alloy. The purpose of this study is to investigate the effect of laser scanning parameters on the epitaxial grain growth and LoF formation in order to obtain the parameter space in which the microstructure is refined and LoF defect is suppressed. The temperature field of the molten pool and the epitaxial grain growth are simulated using a multiscale model combining the finite element method with the phase-field method. The LoF model is proposed to predict the formation of LoF defects resulting from insufficient melting during L-PBF. Defect mitigation and grain-structure control during L-PBF can be realized simultaneously in the model. The simulation shows the input laser energy density for the as-deposited structure with fine grains and without LoF defects varied from 55.0-62.5 J center dot mm(-3) when the interlayer rotation angle was 0 degrees-90 degrees. The optimized process parameters (laser power of 280 W, scanning speed of 1160 mm center dot s(-1), and rotation angle of 67 degrees) were computationally screened. In these conditions, the average grain size was 7.0 mu m, and the ultimate tensile strength and yield strength at room temperature were (1111 +/- 3) MPa and (820 +/- 7) MPa, respectively, which is 8.8% and 10.5% higher than those of reported. The results indicating the proposed multiscale computational approach for predicting grain growth and LoF defects could allow simultaneous grain-structure control and defect mitigation during L-PBF.

Formation and evolution mechanisms of pores in Inconel 718 during selective laser melting: Meso-scale modeling and experimental investigations

Numerical Study of the Pore Defects Formation Mechanisms in Selective Laser Melting Process

Formation mechanisms of lack of fusion and keyhole-induced pore defects in laser powder bed fusion process: A numerical study

Formation of Defects in Selective Laser Melted Inconel 718 and Its Correlation with Mechanical Properties Through Dimensionless Numbers

A Novel Method for the Molten Pool and Porosity Formation Modelling in Selective Laser Melting

Evaluation and Prediction of Pore Effects on Single-Crystal Mechanical and Damage Properties of Selective Laser Melted Inconel-718

Microstructural evolution and mechanical performances of selective laser melting Inconel 718 from low to high laser power

Mesoscopic evolution of molten pool during selective laser melting of superalloy Inconel 738 at elevating preheating temperature

Deformation Behavior of Selective Laser-Melted Inconel 718 Superalloy

Effect of Overlapping Ratio on Forming Quality during Numerical Simulation Selective Laser Melting of Inconel 718 Alloy

Understanding processing parameters affecting residual stress in selective laser melting of Inconel 718 through numerical modeling

Macro-Micro Coupled Simulation of SLM Process with Inconel 718 Superalloy

A New Mesoscale Model for Selective Laser Melting to Unravel the Dependence of Microstructure on Printing Areas for Inconel 625

Evolution Mechanism of Surface Morphology and Internal Hole Defect of 18ni300 Maraging Steel Fabricated by Selective Laser Melting

Phase-field Simulation of Lack-of-fusion Defect and Grain Growth During Laser Powder Bed Fusion of Inconel 718

Impact of Pore Defects on Laser Additive Manufacturing of Inconel 718 Alloy Based on a Novel Finite Element Model: Thermal and Stress Evaluation

Quantification of Interdependent Dynamics during Laser Additive Manufacturing Using X‐Ray Imaging Informed Multi‐Physics and Multiphase Simulation

Anisotropic damage evolution and modeling for a nickel-based superalloy built by additive manufacturing

Influence of shielding gas flow on pore evolution in AlSi10Mg/In718 alloy by laser powder bed fusion

Influence of Laser Post-Processing on Pore Evolution of Ti–6Al–4V Alloy by Laser Powder Bed Fusion