Abstract:Ti6Al4V is widely used in aerospace and medical applications, where high demands on dimensional accuracy and surface quality require the application of post-processing to achieve optimal performance. However, the surface quality of parts fabricated by LPBF is inferior due to the inherent defects of LPBF. Therefore, it is important to investigate the effect of post-processing on the surface quality of Ti6A14V parts fabricated by LPBF. In this work, the effect of post-processing methods (i.e., sandblasting, electrolytic polishing, chemical polishing, and abrasive flow polishing) on the surface quality of Ti6Al4V fabricated by laser powder bed fusion (LPBF) additive manufacturing was investigated. The changes in surface roughness and morphology of the 45° inclined square and curved pipe Ti6Al4V samples processed with post-processing were observed, and the weight and elemental changes of the parts were also analyzed. The result reveals that sandblasting, electrolytic polishing, chemical polishing, and abrasive flow polishing are all effective in improving the surface quality of Ti6Al4V parts fabricated by LPBF. The effect of sandblasting is mainly caused by sharp-edged grit driven by high-speed airflow, resulting in the lowest surface roughness and the least influence on the weight, but may contaminate the surface with residual brown corundum. Electrolytic polishing and chemical polishing achieve surface quality improvement through different corrosion patterns without changing the surface composition. The surface smoothness of parts processed with chemical polishing is the best, while the weight loss rate of the sample processed with electrolytic polishing is the most at about 7.47%. Abrasive flow polishing presents a remarkable effect on polishing the internal surface of the Ti6Al4V sample by the extrusion scratching, extrusion deformation, and micro-cutting effects of abrasive on the surface. The findings can provide important engineering references for the post-processing of precision Ti6Al4V parts fabricated by LPBF and further promote the engineering applications of Ti6Al4V parts.

Surface roughness improvement of Ti-6Al-4V alloy overhang structures via process optimization for laser-powder bed fusion

Study on Surface Roughness Improvement of Selective Laser Melted Ti6Al4V Alloy

Effect of processing parameters on overhanging surface roughness during laser powder bed fusion of AlSi10Mg

Optimising the Process Parameters of Selective Laser Melting for the Fabrication of Ti6Al4V Alloy

Formation and Evolution of Surface Morphology in Overhang Structure of IN718 Superalloy Fabricated by Laser Powder Bed Fusion

Study of the Effect of Selective Laser Melting Process Parameters on Overhang Structures

Surface Roughness Improvement by Sliding Friction Burnishing of Parts Produced by Selective Laser Melting of Ti6Al4V Titanium Alloy

Optimisation of the laser polishing for laser-powder bed fusion and electron beam-powder bed fusion Ti6Al4V surfaces

Study on the Surface Quality of Overhanging Holes Fabricated by Additive/Subtractive Hybrid Manufacturing for Ti6Al4V Alloy

Parameter optimization of selective laser melting fabricated titanium alloy using skin-core and triple contour scanning strategy

Optimization of Processing Parameters and Establishment of a Relationship Between Microstructure and Mechanical Properties of SLM Titanium Alloy

Effect of Post-Processing Methods on the Surface Quality of Ti6Al4V Fabricated by Laser Powder Bed Fusion

Effect of Initial Surface Morphology and Laser Parameters on the Laser Polishing of Stainless Steel Manufactured by Laser Powder Bed Fusion

A study on surface morphology and tension in laser powder bed fusion of Ti-6Al-4V

Experimental Research and Optimization of Ti-6Al-4V Alloy Microgroove Machining Based on Waterjet-Guided High-Power Laser

Overlap ratio and scanning strategy effects on laser powder bed fusion Ti6Al4V: numerical thermal modeling and experiments

A Surface Quality Optimization Strategy Based on a Dedicated Melt-Pool Control Via the Dashed-Scan Contouring Technique in Electron Beam Powder Bed Fusion

Microstructural Evolution and Mechanical Properties of LDED Ti-6Al-4 V Alloy Polished with a Hybrid Laser Polishing Technique

Research Progress on Surface Polishing Technology of Powder Bed Fusion Titanium Alloy

Study on Laser Polishing of Ti6Al4V Fabricated by Selective Laser Melting

Multi-Response Optimization of Ti6Al4V Support Structures for Laser Powder Bed Fusion Systems