Abstract:—This article presents the results of studies of the structure and mechanical properties of high strength austenite chromium-free dispersion hardened Mn–Ni–V–C steel with the yield stress of at least 700 MPa; its composition and hardening method have been selected with consideration that the steel should meet the requirements of high strength and non-magnetization as well as possess a value of electrode potential in chloride media preventing galvanic corrosion during the contact with ferromagnetic low alloy and carbon steels. It has been established that, upon addition of 1–2% Cu to Mn–Ni–V–C steel, on the phase diagram of Fe–Ni–Mn, the region of existence of the γ phase is broadened, and the two phase γ + α region is narrowed and displaced toward lower Mn contents, thus increasing the austenite stability against martensite transformation upon cold deformation. Numerical assessment of the influence of alloying austenite elements Ni, Mn, and Cu on the critical extent of cold plastic deformation leading to formation of deformation martensite in steel is proposed. The temperature range of reverse transformation of this martensite into austenite during annealing has been determined as a function of nickel content in steel. The regularities of dissolution upon heating for quenching and deposition of particles of the hardening carbide phase VC have been studied for dispersion hardened steel with the following composition: 10% Mn; 10% Ni; 2% Cu; 0.3–0.4% C; ~1.4% V. It has been demonstrated that the maximum strength is achieved after quenching from 1150°C and aging at 650°C for 15 h. The cyclic durability of steel increases with the aging duration from 0.7 to 10 h; however, the strength aging close to the maximum leads to a decrease in this performance. Taking into account the performed studies of austenite stability, static and cyclic strength, and durability, the optimum interval of steel alloying with nickel, manganese, and copper has been substantiated, and the optimum mode of thermal tre-atment providing a combination of high strength with good plasticity and toughness of steel has been det-ermined.

Development of high strength interstitial free steel by copper precipitation hardening

Development of high strength steel sheet with improved strainhardenability for automotive application

Design and development of precipitate strengthened advanced high strength steel for automotive application

Enhanced High‐Temperature Strength of a Low‐Density Dispersion‐Strengthened Fe–Mn–Al–C Steel

High Strength Austenite Mn–Ni–Cu–V–C Dispersion Hardened Steel

New developments of advanced high-strength steels for automotive applications

Strengthening of Ni-Mn-Cu-Al-Co steel by nanoscale Cu and β-NiAl co-precipitated couples

Effect of Copper Content and Heat Treatment Schedules on Mechanical Properties, Cold Resistance, and Microstructural Constituent Morphology in Precipitation-Hardened Steel

Attainment of an exceptionally high strength in low-carbon steel along with modest ductility through a novel heat treatment route

Influence of TMCP Parameters on Structure and Properties of Low Carbon Cu Bearing Ultra-High Strength Steel

Introducing Heusler intermetallics for synergic effect of grain refinement and precipitation strengthening in high-strength low-alloy steels

Development of a Silicon Alloyed Hardened and Tempered Ultra High Strength Steel

Structure and mechanical properties of high strength austenitic Mn–Ni–Cu–V–C dispersionally hardened steel

Improvement of Resistance to Hydrogen Embrittlement for 1300MPa Ultra-high Strength Steel by Introducing Nano-sized Cu-rich Phase Precipitation

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

Nanoscale Cu particle evolution and its impact on the mechanical properties and strengthening mechanism in precipitation-hardening stainless steel

Developing High-Strength in a Deep Drawing Steel by a Post-Cold Rolling Nitriding Treatment

Recent Advancements in Copper Infiltration Applied to Sintered Steel

Recent development of advanced precipitation-strengthened Cu alloys with high strength and conductivity: A review

Diffusional and displacive transformations in interstitial-free steel within the scope of a critical assessment of the mechanical property

Industrial implementation of a next generation advanced high strength steel