Abstract:Lead-free double perovskite Cs2AgBiBr6 is considered to serve as a substitute for toxic lead-based perovskite components and is a promising candidate for environmentally friendly perovskite solar cells (PSCs). However, the high deep-level trap density in Cs2AgBiBr6 films hinders the device performance, which is caused by the different solubilities of components in the precursor solution and the solution-process fabrication method. In this work, we reported a surface reconstruction (SR) strategy, in which a dissolution process is initiated by dimethyl sulfoxide (DMSO) and followed by the introduction of methylammonium bromide (MABr) to generate a mixed organic-inorganic intermediate phase and induce an orderly recrystallization. The dissolution-recrystallization process effectively improves the overall crystalline quality and surface composition stoichiometry ratio, passivates the bromine vacancies enriched in the film, and forms a dense as well as ordered film surface, resulting in reduced trap density, extended carrier lifetime, better interfacial contact, and faster carrier extraction. The differences in underlying mechanisms and effects between the conventional interfacial passivation (IP) strategy based on the passivator/isopropanol (IPA) system and the SR strategy proposed in this work were also compared by multiple characterizations. All these advantages enable the Cs2AgBiBr6-based PSCs fabricated by the SR strategy to achieve a significantly higher power conversion efficiency (PCE) of 2.05% and an ultrahigh fill factor (FF) of 83.80% as well as open-circuit voltage (V (OC)) of 1.201 V, with good stability and broad applicability in the hole transport layer (HTL)-free PSCs. Therefore, this work points out the fundamentally different mechanisms of two post-treatment strategies on the overall regulation of Cs2AgBiBr6 films and provides a clear clue to further enhance the quality of lead-free double perovskite films and optimize the photovoltaic performance of PSCs.

Synergistic effects of morphological control and enhanced charge collection enable efficient and stable lead-free CsBi 3 I 10 thin film solar cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Antimony Doping of CsBi 3 I 10 for Tailoring the Film Morphology and Defects toward Efficient Lead-Free Thin-Film Solar Cells

Bismuth Complex Controlled Morphology Evolution and CuSCN-Induced Transport Improvement Enable Efficient BiI3 Solar Cells

Synergistic Improvement of Perovskite Film Quality for Efficient Solar Cells Via Multiple Chloride Salt Additives

Octylammonium Octyldithiocarbamate Assisted Modulation of Crystallization and Doping of In Situ‐Generated Lead Sulfide for Efficient and Highly Stable Carbon‐Based CsPbIBr2 Solar Cells

Quantum Dot Interface-Mediated CsPbIBr 2 Film Growth and Passivation for Efficient Carbon-Based Solar Cells

Synergetic interfacial passivation, band alignment, and long-term stability with halide-optimized CsPbBr x I 3− x nanocrystals for high-efficiency MAPbI 3 solar cells

Carbohydrazide-Assisted Morphology and Structure Controlling for Lead-Free Cs 2 AgBiBr 6 Double Perovskite Solar Cells

Controlling the Intermediate Phase to Improve the Crystallinity and Orientation of Cs3Sb2ClxI9‐x Films for Efficient Solar Cells

Passivating A-Site and X-Site Vacancies Simultaneously Via N-Heterocyclic Amines for Efficient Cs2AgBiBr6 Solar Cells.

Control of the Morphology of PbI2 Films for Efficient Perovskite Solar Cells by Strong Lewis Base Additives

Solvent-Engineering-Assisted Ligand Exchange Strategy for High-Efficiency AgBiS2 Quantum Dot Solar Cells

Synthesis and Optimization of Cs2B′B′′X6 Double Perovskite for Efficient and Sustainable Solar Cells

Improved charge extraction and atmospheric stability of all-inorganic Cs2AgBiBr6 perovskite solar cells by MoS2 nanoflakes

Composition Stoichiometry of Cs2AgBiBr6 Films for Highly Efficient Lead-Free Perovskite Solar Cells

Synergistic Modulation of Sn-Based Perovskite Solar Cells with Crystallization and Interface Engineering

Modulating Residual Lead Iodide via Functionalized Buried Interface for Efficient and Stable Perovskite Solar Cells

First Investigation of Additive Engineering for Highly Efficient Cs2AgBiBr6-based Lead-Free Inorganic Perovskite Solar Cells

Synergistic Crystallization Modulation and Defects Passivation in Kesterite via Anion-Coordinate Precursor Engineering for Efficient Solar Cells

Surface Reconstruction for Efficient Cs2AgBiBr6 Solar Cells