Abstract:Abstract A radiofrequency (RF) ion source with a megawatt power extraction, thunder I, has been developed for the neutral beam injector (NBI) on HL-2A tokamak. A full solid-state RF generator with output power of 80 kW and frequency of 2 MHz was built by an RF combiner using 8 modules of solid-state RF generator with power of P RF = 10 kW. The line electric efficiency of whole RF generator reaches 92% and its voltage standing wave ratio (VSWR) is 1.01, thus no water-cooling system is supplied. A quartz vessel with the inner diameter of 250 mm is directly adopted for resisting atmospheric pressure, which can dramatically simplify source structure. Nowadays, the extracted beam parameters of RF hydrogen ion source are 32 kV/20 A/0.1 s on a test bed, while the design parameters are 50 kV/20 A/3 s. The beam density profile measured by the infrared imaging technique at 1.3 m downstream from the grounded grid obeys a Gaussian distribution, and the corresponding half width of 1/ e power decay at the matched condition is about 80 mm. Plasma homogeneity is over 90% at low RF power. The beam divergence angle meets the requirement of NBI system on HL-2A tokamak. The extractable current density increases almost linearly with the RF power. It reaches 2400 A m −2 at P RF = 32 kW. The ion density in front of plasma grid is about 1 × 10 18 m −3 , corresponding to an ionized fraction of about 1% at the gas pressure of 0.5 Pa. Single hydrogen ion fraction reaches 79% at the beam current of 12.4 A. Some improvements have been considered for optimizing ion source performance on next experimental campaign. One smaller auxiliary RF discharge chamber equipped with a gas feed path, driven by 13.56 MHz/3.5 kW generator, is connected to main discharge chamber driven by 2 MHz/40 kW generator. By this dual-driven configuration, the innovative RF plasma source with high-pressure density gradient solves the initial ignition problem of powerful RF ion source even if the gas pressure below 0.1 Pa. In addition, the RF negative hydrogen ion source of 200 kV/20 A/3600 s is also developed at SWIP for the China fusion engineering test reactor.

Development of a 50 kV hydrogen–helium mixed ion beam implanter

High-Power Ion Beam Characteristics of a Magnetic Multi-Pole Line-Cusp Ion Source for the HL-2A Tokomak

Conceptual design of 5 MW-NBI injector for HL-2 M tokamak

Design of a Beam Line for Simultaneous Dual-Beam Ion Implantation

Development of the Special Beam Line at HI 13 Tandem Accelerator for Irradiation of Nuclear Track Membrance

Development of a negative helium ion source with non-metallic charge exchange

Development of megawatt radiofrequency ion source for the neutral beam injector on HL-2A tokamak

Polyatomic ions from a high current ion implanter driven by a liquid metal ion source

High current H2(+) and H3(+) beam generation by pulsed 2.45 GHz electron cyclotron resonance ion source.

Commissioning of Helium Injector for Coupled Radio Frequency Quadrupole and Separated Function Radio Frequency Quadrupole Accelerator

Beam dynamic design of a high intensity injector for proton linac

Possibility of Generating H+, or H2+, or H3+ Dominated Ion Beams with a 2.45 GHz Permanent Magnet ECR Ion Source

Milliampere He 2 + Beam Generator Using a Compact GHz ECRIS

High-Fluence Multi-Energy Ion Irradiation for Testing of Materials

Successful High Power Acceleration of the HSC Type Injector for Cancer Therapy in IMP

High current $\mathrm{H}_2^+$ beams from a filament-driven multicusp ion source

Status of the Los Alamos heavy ion injector

Design of a 4 MeV/u IH-DTL Injector for Cancer Therapy

Design of a Facility for Simultaneous Irradiation with Two Ion Beams based on the HIPR Accelerator for Simulations Neutron Influence

CW/Pulsed H− Ion Beam Generation with PKU Cs-free 2.45 GHz Microwave Driven Ion Source

The Deuteron Injector Progress of the Peking University Neutron Imaging Facility Project.