Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Comparative analysis of mechanical characteristics in masonry walls: impact of aspect ratios and opening percentages

Influence of Confining Element Stiffness on the In-Plane Seismic Performance of Confined Masonry Walls

Experimental Study of RC Frames with Window and Door Openings Under Cyclic Loading

Effects of aspect ratios and vertical loads on in-plane seismic behavior of unreinforced masonry walls: A numerical simulation

Comparative Studies of the Confined Effect of Shear Masonry Walls Made of Autoclaved Aerated Concrete Masonry Units

Analytical modeling of masonry load-bearing walls

Shear Behaviour of Reinforced Concrete Structural Walls with Eccentric Openings under Cyclic Loading: Experimental Study

Backbone Model for Confined Masonry Walls for Performance-Based Seismic Design

Improving In-Plane Behavior of Weak Brick Masonry Walls Through Assimilation of Partially Confining RC Bands

Finite element-based reliability analysis of reinforced concrete masonry walls under eccentric axial loading considering slenderness effects

Title : In-situ out-of-plane testing of as-built and retrofitted unreinforced masonry walls 1

Evaluating the Role of Mortar Composition on the Cyclic Behavior of Unreinforced Masonry Shear Walls

Experimental and numerical investigation of hysteretic earthquake behavior of masonry infilled RC frames with opening strengthened by adding rebar-reinforced stucco

Experimental Analysis of Out-of-plane Behavior of Masonry Infill Walls Strengthened with Textile Reinforced Mortar and Wall Post in Autoclaved Aerated Concrete Frames

Investigating the confinement effects on masonry behavior based on friction interface

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

Analytical Model for the In-Plane Lateral Capacity of Unreinforced Masonry Walls Based on Effective Compression Zone Failure Mechanism

An improved method for statistics estimation of out-of-plane load resistance of masonry walls using design-code models and mechanics-based finite element models

Experimental and Numerical Study on the Seismic Performance of Prefabricated Reinforced Masonry Shear Walls

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Numerical investigation on the effect of infill masonry on lateral behaviour of surrounding RC frame