Abstract:Purpose Fused filament fabrication (FFF) technique using metal filled filaments in combination with debinding and sintering steps can be a cost-effective alternative for laser-based powder bed fusion processes. The mechanical behaviour of FFF-metal materials is highly dependent on the processing parameters, filament quality and adjusted post-processing steps. In addition, the microstructural material properties and geometric characteristics are inherent to the manufacturing process. The purpose of this study is to characterize the mechanical and geometric performance of three-dimensional (3-D) printed FFF 316 L metal components manufactured by a low-cost desktop 3-D printer. The debinding and sintering processes are carried out using the BASF catalytic debinding process in combination with the BASF 316LX Ultrafuse filament. Special attention is paid on the effects of build orientation and printing strategy of the FFF-based technology on the tensile and geometric performance of the 3-D printed 316 L metal specimens. Design/methodology/approach This study uses a toolset of experimental analysis techniques [metallography and scanning electron microcope (SEM)] to characterize the effect of microstructure and defects on the material properties under tensile testing. Shrinkage and the resulting porosity of the 3-D printed 316 L stainless steel sintered samples are also analysed. The deformation behaviour is investigated for three different build orientations. The tensile test curves are further correlated with the damage surface using SEM images and metallographic sections to present grain deformation during the loading progress. Mechanical properties are directly compared to other works in the field and similar additive manufacturing (AM) and Metal Injection Moulding (MIM) manufacturing alternatives from the literature. Findings It has been shown that the effect of build orientation was of particular significance on the mechanical and geometric performance of FFF-metal 3-D printed samples. In particular, Flat and On-edge samples showed an average increase in tensile performance of 21.7% for the tensile strength, 65.1% for the tensile stiffness and 118.3% for maximum elongation at fracture compared to the Upright samples. Furthermore, it has been able to manufacture near-dense 316 L austenitic stainless steel components using FFF. These properties are comparable to those obtained by other metal conventional processes such as MIM process. Originality/value 316L austenitic stainless steel components using FFF technology with a porosity lower than 2% were successfully manufactured. The presented study provides more information regarding the dependence of the mechanical, microstructural and geometric properties of FFF 316 L components on the build orientation and printing strategy.

Fabrication of Thin-Wall Structures with a Femtosecond Laser and Stainless Steel Powder

Investigation of Fabricating Stainless Steel 304L Thin-Wall Structure Using Laser Marking-Assisted Wire Arc Additive Manufacturing Process

Influence of wall thickness on microstructure and mechanical properties of thin-walled 316L stainless steel produced by laser powder bed fusion

Recent Progress on 3D Printing of Lightweight Metal Thin‐Walled Structures

Laser powder bed fusion additively manufactured thin lightweight Ti6Al4V features: an experimental investigation on the influence of powder feedstock, geometry, and process parameters on property/quality

Macroscopic and Microstructural Features of Metal Thin-Wall Fabricated by Laser Material Deposition: A Review

Additive manufacturing of 316L stainless-steel structures using fused filament fabrication technology: mechanical and geometric properties

Investigation on Forming Process and Product Properties of Laser Wire-Feed Additive Manufacturing for High-Quality Metal Thin-Walled Parts

Achieving Triply Periodic Minimal Surface Thin-Walled Structures by Micro Laser Powder Bed Fusion Process

The Influence of Laser Power and Scan Speed on the Dimensional Accuracy of Ti6Al4V Thin-Walled Parts Manufactured by Selective Laser Melting

Dynamics of pore formation during laser powder bed fusion additive manufacturing

The interplay of local chemistry and plasticity in controlling microstructure formation during laser powder bed fusion of metals

Improving the Formability and Quality of CMT Additively Manufactured Aluminum Thin-Wall Parts Via Laser Stabilization Effect

Microstructural Control of a Multi‐Phase PH Steel Printed with Laser Powder Bed Fusion

Fabrication of complex three-dimensional metallic microstructures based on femtosecond laser micromachining

Research on High Layer Thickness Fabricated of 316L by Selective Laser Melting

Additive manufacturing of Ti-6Al-4V alloy by micro-laser metal wire deposition with pulsed wave emission: processability and microstructure formation

Investigating the Effects of Powder Feeding Rate on Microstructure Transformation in Linear Laser Beam Additive Manufactured Thick-Walled Structures

Microstructure Tailoring for High Strength Ti-6Al-4V without Alloying Elements through Optimized Preheating and Post-Heating Laser Scanning in Laser Powder Bed Fusion

Selective Laser Melting Technology and Manufacturing of Accurate Thin Structures

Micro/Nano Periodic Surface Structures and Performance of Stainless Steel Machined Using Femtosecond Lasers