Abstract:Wire-based laser directed energy deposition (LDED) technology is an attractive and efficient additive manufacturing technology, which shows great potential in the process of manufacturing high-value engineering components. However, the thermal effect will lead to a large amount of residual tensile stress in the components, and the large crystal structures after solidification seriously affects the tensile performance. The pursuit of high mechanical properties in additive manufacturing components have prompted researchers to seek new strengthening process to produce high-strength components. Therefore, in this paper, laser shock peening (LSP) composite wire-based LDED were used for the additive manufacturing of 17-4 PH stainless steel under the specified experimental conditions, and the effects of LSP on microstructure evolution, microhardness, and tensile properties of wire-based LDED components were systematically studied. Results showed that uniform grains with an average size of 2.31 mu m were generated on the top surface of specimen due to the ultra-high plastic strain induced by LSP shock wave. The size of hierarchical martensitic units shows varying degrees of reduction after LSP treatment, which is shown by the width decrease of packet, block and lath. Dynamic recrystallization caused by rearrangement and annihilation of high-density dislocations promoted the grain refinement. Meanwhile, the residual stress was completely converted from tensile state into compressive state with a maximum value of 425 MPa, and the microhardness was also enhanced to a peak value of 432 HV. In addition, we observed that the high-density dislocation environment created by LSP treatment promoted the further precipitation, and the aggregation phenomenon of precipitates was observed in the dense dislocation area. Furthermore, the tensile strength and elongation of LSP treated specimen were improved significantly, which was attributed to the combined effects of grain refinement, introduction of dislocation structures, precipitation strengthening and gradient residual compressive stress. In summary, laser hybrid additive manufacturing technology provides a new idea and method for the production of high-performance precipitation hardening stainless steel components.

Investigation of Fabricating Stainless Steel 304L Thin-Wall Structure Using Laser Marking-Assisted Wire Arc Additive Manufacturing Process

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Mechanical Properties, Microstructural Characteristics and Heat Treatment Effects of WAAM Stainless-Steel Plate Material

Improve the Manufacturing Efficiency of Steel Bars by Using Hot-Wire Pulse Arc Additive Manufacturing

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process

Mechanical behavior of austenitic stainless steels produced by wire arc additive manufacturing

Fabrication of Bimetallic Structure (SS 316L/SS 308L) via Wire + Arc Additive Manufacturing: A Detailed Characterization of Interface

Tensile properties and microstructural features of 304L austenitic stainless steel produced by wire-and-arc additive manufacturing

Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

A Comparative Study of Microstructural Characteristics and Mechanical Properties of High-Strength Low-Alloy Steel Fabricated by Wire-Fed Laser Versus Wire Arc Additive Manufacturing

Effects of laser additive manufacturing on microstructure and crystallographic texture of austenitic and martensitic stainless steels

Microstructural Evolution in a Thin Wall of 2cr13 Martensitic Stainless Steel During Wire Arc Additive Manufacturing

Investigation on Forming Process and Product Properties of Laser Wire-Feed Additive Manufacturing for High-Quality Metal Thin-Walled Parts

Study on Heat Input Effect of 316L Stainless Steel Thin-Walled Parts Processed by Wire Arc Additive Manufacturing

Tensile Properties and Microstructural Evolution of 17–4 PH Stainless Steel Fabricated by Laser Hybrid Additive Manufacturing Technology

Laser Welding of AISI 316L Stainless Steel Produced by Additive Manufacturing or by Conventional Processes

Effect of wire arc additive manufacturing parameters on geometric, hardness, and microstructure of 316LSi stainless steel preforms

Macroscopic and Microstructural Features of Metal Thin-Wall Fabricated by Laser Material Deposition: A Review

Fabrication of Thin-Wall Structures with a Femtosecond Laser and Stainless Steel Powder