Abstract:Additive manufacturing technology overcomes the limitations imposed by traditional manufacturing techniques, such as fixtures, tools, and molds, thereby enabling a high degree of design freedom for parts and attracting significant attention. Combined with subtractive manufacturing technology, additive and subtractive hybrid manufacturing (ASHM) has the potential to enhance surface quality and machining accuracy. This paper proposes a method for simulating the additive and subtractive manufacturing process, enabling accurate deformation prediction during processing. The relationship between stress distribution and thermal stress deformation of thin-walled 316L stainless steel parts prepared by Laser Metal Deposition (LMD) was investigated using linear scanning with a laser displacement sensor and finite element simulation. The changes in stress and deformation of these thin-walled parts after milling were also examined. Firstly, 316L stainless steel box-shaped thin-walled parts were fabricated using additive manufacturing, and the profile information was measured using a Micro Laser Displacement Sensor. Then, finite element software was employed to simulate the stress and deformation of the box-shaped thin-walled part during the additive manufacturing process. The experiments mentioned were conducted to validate the finite element model. Finally, based on the simulation of the box-shaped part, a simulation prediction was made for the box-shaped thin-walled parts produced by two-stage additive and subtractive manufacturing. The results show that the deformation tendency of outward twisting and expanding occurs in the additive process to the box-shaped thin-walled part, and the deformation increases gradually with the increase of the height. Meanwhile, the milling process is significant for improving the surface quality and dimensional accuracy of the additive parts. The research process and results of the thesis have laid the foundation for further research on the influence of subtractive process parameters on the surface quality of 316L stainless steel additive parts and subsequent additive and subtractive hybrid manufacturing of complex parts.

Investigation on Forming Process and Product Properties of Laser Wire-Feed Additive Manufacturing for High-Quality Metal Thin-Walled Parts

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Forming Process, Microstructure, and Mechanical Properties of Thin-Walled 316L Stainless Steel Using Speed-Cold-Welding Additive Manufacturing

Effect of Laser Scanning and Powder Addition on Microstructure and Mechanical Properties for Hot-Wire-Feed Laser Additive Manufacturing

Microstructure and Mechanical Properties of Ti-6Al-4V Fabricated by Vertical Wire Feeding with Axisymmetric Multi-Laser Source

The Effect of Low-Power Laser on Micro-Forming of 316 Stainless Steel Additive Manufacturing Part

Morphologies, Microstructures, and Mechanical Properties of Samples Produced Using Laser Metal Deposition with 316 L Stainless Steel Wire

Surface Quality and Forming Characteristics of Thin-Wall Aluminium Alloy Parts Manufactured by Laser Assisted MIG Arc Additive Manufacturing

Improving the Formability and Quality of CMT Additively Manufactured Aluminum Thin-Wall Parts Via Laser Stabilization Effect

316L Stainless Steel Thin-Walled Parts Hybrid-Layered Manufacturing Process Study

Low-Roughness-Surface Additive Manufacturing of Metal-Wire Feeding with Small Power

A Study of Multi-Layer Multi-Pass Laser Depositing with 316L Stainless Steel Wire

Investigation of Fabricating Stainless Steel 304L Thin-Wall Structure Using Laser Marking-Assisted Wire Arc Additive Manufacturing Process

Coaxial Laser Metal Wire Deposition of Ti6Al4V Alloy: Process, Microstructure and Mechanical Properties

A Novel Strategy to Fabricate Thin 316L Stainless Steel Rods by Continuous Directed Energy Deposition in Z Direction

A Comparative Study of Microstructural Characteristics and Mechanical Properties of High-Strength Low-Alloy Steel Fabricated by Wire-Fed Laser Versus Wire Arc Additive Manufacturing

Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing

Enhanced mechanical properties and formability of 316L stainless steel materials 3D-printed using selective laser melting

Macroscopic and Microstructural Features of Metal Thin-Wall Fabricated by Laser Material Deposition: A Review