Abstract:1.4418 hardened stainless steel (SS) is widely used in mechanical engineering because of its high functional properties. They can also be enhanced by procuring improvements in the state of the surface layer (SL) and, above all, in the factors of its strengthening, among others the average size of coherent scattering regions (ASCSR), dislocation density (DD), residual stresses (RS) of first and second orders, and relative micro-deformations of the crystal lattice (RMCL). This study investigates the effect of cutting speed ( v c ) ranging from 100 to 250 m/min and feed rate ( f ) ranging from 0.005 to 0.25 mm/rev on the indicators of SL condition after finish turning the steel tested. A reduction in ASCSR values below 8 nm was obtained for v c = 100–135 m/min, while an increase of ~ 20% was obtained for 180–250 m/min and with the f ranging from 0.2 to 0.25 mm/rev. An increase in RMCL of ~ 90% was registered for v c = 170–230 m/min and f = 0.2–0.25 mm/rev. A decrease in DD below 10 9 cm −2 was obtained for v c = 180–250 m/min and its ~ 25% increase for v c = 100–135 m/min. A high correlation between ASCSR and DD was shown. In the deformed material, the dislocation's resistance to motion increases in proportion to the increase in its density. A high linear correlation coefficient in the range of 0.8–0.9 is found between ASCSR, DD, and first-order RS on the one hand, and Sa and Sz surface texture parameters, which are used in the industry to assess product quality, on the other. Additionally, the effect of plastic side flow (PSF) was observed and described. When machining with v c = 119 m/min and f = 0.22 mm/rev, the intense plastic deformation of the material causes outflow and shearing of the surface micro-hills. Favorable compressive stresses (below − 100 MPa) were registered in the range of v c = 225–250 m/min at f = 0.005–0.05 m/rev and 0.2–0.25 mm/rev, as well as v c = 115–180 m/min and f = 0.05–0.17 mm/rev. The study proved the existence of a relationship between the cutting parameters and indicators of the thin crystalline structure of SL. This means that by proper controlling of these parameters, it is possible to obtain such a state of the SL workpiece, which will ensure its long-term use.

Surface integrity and modification of SA508Gr.3Cl.2 RPV steel induced by high-speed face milling process

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Surface modification of ultrahigh strength 300M steel under supercritical carbon dioxide (scCO2)-assisted grinding process

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Microstructure evolution and surface strengthening behavior of 300 M ultrahigh strength steel under engineered surface treatments

Adapting the Surface Integrity of High-Speed Steel Tools for Sheet-Bulk Metal Forming

Inconel 625 sustainable milling surface integrity and the dependence on alloy processing route

Distinguishing effect of turning and grinding on the surface integrity and fatigue performance of ultra-high strength steel

Tool failure mechanisms and cutting performance analysis during high-feed milling of 508-III steel

The Surface Integrity in Machining Hardened Steel Skd11 for Die and Mold

Experimental investigations on surface integrity and chip morphology in hard tuning of AISI D3 steel under sustainable nanofluid-based minimum quantity lubrication

The Comparative Studies on the Surface Integrity in Milling and Grinding Hardened Steel SKD11

Study on improving surface integrity for additively manufactured Inconel 718 via high-speed micromilling

Investigation on surface integrity in milling of Inconel X750: A comprehensive analysis of cutting edges and machining parameters

Machinability of a Sinter-Hardened Powder Metallurgy Steel: Combined Analysis of Cutting Force and Chip Characteristics

Unravelling microstructure evolution mechanism within machined subsurface during turning of laser powder bed fusion-manufactured Inconel 625

Enhanced Wear Properties of an Inspired Fish-Scale Film Structure in Terms of Microstructured Self-Lubrication Induced Effects by High-Speed Laser Surface Remelting Processing

Fine evaluation of surface integrity of hardened 1.4418 stainless steel after finish dry turning

New layering strategy and the gradient microstructure distribution of surface metamorphic layer for 8Cr4Mo4V steel by grinding

Effects of ultrasonic nanocrystal surface modification on the surface integrity, microstructure, and wear resistance of 300M martensitic ultra-high strength steel

Surface Microstructure Refinement and Mechanical Properties of GCr15 Steels Improved During Ultrasonic Surface Rolling Processing