Abstract:Additive manufacturing (AM) introduces unique grain feature and anisotropy in metals, as well as relatively poor surface quality, so the knowledge about the formation of post-machining-induced surface integrity needs to be extended. This study aims to understand the machining phenomena in orthogonal cutting of Inconel 718 produced via powder bed fusion of metals using a laser beam system (PBF-LB/M), paying particular attention to the cutting energy, chip formation, geometrical defects, and microstructural deformation. Experiments are conducted on both wrought (W 718) and PBF-LB/M (PBF 718) Inconel 718, whereby the cutting speed and the anisotropy of the workpiece in the raw state play an important role. The results indicate that less cutting energy is consumed when cutting PBF 718 in the direction perpendicular to its build direction (BD), followed by cutting in its BD. Denser shearing-induced slip lines and relatively continuous chip morphology are found when cutting PBF 718 in its BD, moreover, the effect of cutting speed on shearing deformation of columnar grains under this condition is analysed. More importantly, this study identifies a significant geometrical defect phenomenon which is unique to PBF 718 and highly depends on the cutting speed and anisotropy of grain feature. A detailed characterisation shows that this behaviour is caused by tearing within the grains in the matrix material and not by the presence of hard inclusions, which has rarely been reported in the literature. The microstructure in the subsurface area exhibits that the density of grain boundaries in the cutting direction plays the key role in plastic deformation, as the machining process mainly causes dragging behaviour in the area below the machined surface. Thus, cutting PBF 718 in the direction perpendicular to its BD shows similar deformation layer to W 718, while cutting PBF 718 in its BD displays much stronger subsurface deformation. The obtained results greatly help to understand the cutting phenomena in post-machining of additively manufactured Ni-based components, especially the integrity for a better functional surface.

Study on improving surface integrity for additively manufactured Inconel 718 via high-speed micromilling

Investigation on surface integrity in milling of Inconel X750: A comprehensive analysis of cutting edges and machining parameters

EXPERIMENTAL INVESTIGATION ON SURFACE INTEGRITY OF END MILLING NICKEL-BASED ALLOY— INCONEL 718

Surface roughness optimization of hybrid PBF-LB/M-built Inconel 718 using in situ high-speed milling

Study on surface texture and corrosion resistance of ultrasonic vibration-assisted micromilling Inconel718

On machining-induced surface integrity of Inconel 718 fabricated by powder bed fusion

Optimization of superalloy Inconel 718 micro-milling process by combined Taguchi and multi-criteria decision making method

Atmospheric pressure plasma jet assisted micro-milling of Inconel 718

Machinability Evaluation and Surface Characteristics in Post-machining of Inconel 625 Fabricated by Laser Powder-Bed Fusion

Relationship Between Energy Efficiency and Surface Morphologies in Micro-Milling of SLM Inconel 718

Surface Integrity Improvement of the Ground Surface of Inconel 718 Fabricated by Forging and Additive Manufacturing Using a Robotic Rotational Burnishing Method

Grindability of additively manufactured Inconel 718

Machinability of INCONEL718 Alloy with a Porous Microstructure Produced by Laser Melting Powder Bed Fusion at Higher Energy Densities

Surface Microstructure Evolution and Mechanical Property Investigation of Inconel 718 Alloy Using Multiple Trimmings and WEDM

Post-processing effects on the surface characteristics of Inconel 718 alloy fabricated by selective laser melting additive manufacturing

Surface quality analysis in ball end milling of Inconel 718 cantilevers by response surface methodology

Surface Integrity of Inconel 718 in High-Speed Electrical Discharge Machining Milling Using Air Dielectric

Influence of abrasive deburring in indirect tool wear measurement in micromilling of Inconel 718

Experimental Investigation on Laser-Processed Micro-Dimple and Micro-Channel Textured Tools during Turning of Inconel 718 Alloy

Experimental Study on the Effect of Cutting Tool Geometry in Micro-Milling of Inconel 718

Depth-Resolved Characterization of Centrifugal Disk Finishing of Additively Manufactured Inconel 718