Abstract:As one of the most important surface strengthening method, shot peening is widely used to improve the fatigue and stress corrosion crack resistance of components by introducing the refined microstructure and compressive residual stress in the surface layer. However, the mechanical properties of this thin layer are different from the base metal and are difficult to be characterized by conventional techniques. In this work, a micro uniaxial tensile tester equipped with in-situ X-ray stress analyzer was employed to make it achievable on a nickel-aluminum bronze with shot peening treatment. According to the equivalent stress-strain relationship based on Von Mises stress criterion, the Young's modulus and yield strength of the peened layer were calculated. The results showed that the Young's modulus was the same as the bulk material, and the yield strength corresponding to the permanent plastic strain of 0.2% was increased by 21% after SP. But the fractographic analysis showed that the fracture feature of the surface layer was likely to transform from the dimple to the cleavage, indicating the improved strength might be attained at the expense of ductility. The monotonic and cyclic loading were also performed via the same combined setup. In addition, the specific relaxation behavior of compressive residual stress was quantified by linear logarithm relationship between residual stress and cycle numbers. It was found that the compressive residual stress mainly relaxed in the first few cycles, and then reached steady state with further cycles. The relaxation rate and the stable value were chiefly depended on the stress amplitude and number of cycles. The retained residual stress kept in compressive under all given applied stress levels, suggesting that the shot peening could introduce a more stable surface layer of compressive residual stress other than the elevated strength of nickel-aluminum bronze alloy. (C) 2017 Elsevier B.V. All rights reserved.

Characterization of distribution of residual stress in shot-peened layer of nickel-based single crystal superalloy DD6 by nanoindentation technique

Characterization of Distribution of Microstructure and Micro-mechanical Properties of Nickel-Based Single Crystal Superalloy Within the Shot-Peened Layer

Investigation of fatigue mesoscopic mechanical properties of a nickel-based superalloy by instrumented microindentation measurements

X-ray Diffraction Analysis for Residual Stress in Shot Peened Layer of DD3 Nickel-Based Single Crystal High Temperature Alloy

A Study of Fatigue Mesoscopic Elasto-Plastic Properties of a Nickel-Base Superalloy by Instrumented Microindentation Measurements

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

Influence of Shot Peening on Surface-Layer Characteristics of a Monocrystalline Nickel-Based Superalloy

Effect of Shot Peening on Surface Characteristics of Ni-Based Single-Crystal Superalloy

Size effect of nickel-based single crystal superalloy revealed by nanoindentation with low strain rates

Simulations of the effect of shot peening backstress on nanoindentation

Mechanical Properties of Micro-phases Along < 001 > Direction of Directionally Solidified Nickel-base Super-alloy by In-situ Nano-Indentation

XRD Measurement of Residual Stress of Nickel-Based Monocrystalline Superalloy AM1

Grinding surface and subsurface stress load of nickel-based single crystal superalloy DD5

Effect of stress shot peening on the residual stress field and microstructure of nanostructured Mg-8Gd-3Y alloy

Surface Mechanical Property and Residual Stress of Peened Nickel-Aluminum Bronze Determined by In-Situ X-Ray Diffraction

Measuring the effect of residual stress on the machined subsurface of Inconel 718 by nanoindentation

Investigation on Experiments and Numerical Modelling of the Residual Stress Distribution in Deformed Surface Layer of Ti–6Al–4V after Shot Peening

Mapping of three-dimensional residual stresses by neutron diffraction in nickel-based superalloy discs prepared under different quenching conditions

Nanoscale microstructural factors contributing to the improvement of the micromechanical wear properties of mechanical shot-peened nickel-based superalloys

Micro-texture and residual stress evolution in shot peened superelastic Ni-Ti/Ni-Ti-Co shape memory alloys